Question

Physical Units Method, Relative Sales-Value-at-Split-off Method, Net Realizable Value Method, Decision Making

Sonimad Sawmill, Inc. (SSI), purchases logs from independent timber contractors and processes them into the following three types of lumber products:

1. Studs for residential construction (e.g., walls and ceilings)
2. Decorative pieces (e.g., fireplace mantels and beams for cathedral ceilings)
3. Posts used as support braces (e.g., mine support braces and braces for exterior fences around ranch properties)

These products are the result of a joint sawmill process that involves removing bark from the logs, cutting the logs into a workable size (ranging from 8 to 16 feet in length), and then cutting the individual products from the logs, depending upon the type of wood (pine, oak, walnut, or maple) and the size (diameter) of the log.

The joint process results in the following costs and output of products during a typical month:

Joint production costs:
Materials (rough timber logs)	$500,000
Debarking (labor and overhead)	50,000
Sizing (labor and overhead)	200,000
Product cutting (labor and overhead)	250,000
Total joint costs	$1,000,000

Product yield and average sales value on a per-unit basis from the joint process are as follows:

Product	Monthly Output	Fully Processed Sales Price
Studs	70,000	$8
Decorative pieces	5,000	100
Posts	25,000	20

The studs are sold as rough-cut lumber after emerging from the sawmill operation without further processing by SSI. Also, the posts require no further processing. The decorative pieces must be planed and further sized after emerging from the SSI sawmill. This additional processing costs SSI $80,000 per month and normally results in a loss of 10 percent of the units entering the process. Without this planing and sizing process, there is still an active intermediate market for the unfinished decorative pieces where the sales price averages $60 per unit.

Required:

1. Based on the information given for Sonimad Sawmill, Inc., allocate the joint processing costs of $1,000,000 to each of the three product lines using the:

a. Relative sales-value-at-split-off method. When required, round decimal values to four places before converting to a percentage. For example, .88349 would be rounded to .8835 and entered as "88.35" percent.

	Monthly Unit Output	Sales Price per Unit	Relative Sales Value at Split-Off	Percent of Sales		Allocated Joint Costs
Studs	fill in the blank 193db3fcd000ff8_1	$fill in the blank 193db3fcd000ff8_2	$fill in the blank 193db3fcd000ff8_3	fill in the blank 193db3fcd000ff8_4	%	$fill in the blank 193db3fcd000ff8_5
Decorative pieces	fill in the blank 193db3fcd000ff8_6	fill in the blank 193db3fcd000ff8_7	fill in the blank 193db3fcd000ff8_8	fill in the blank 193db3fcd000ff8_9	%	fill in the blank 193db3fcd000ff8_10
Posts	fill in the blank 193db3fcd000ff8_11	fill in the blank 193db3fcd000ff8_12	fill in the blank 193db3fcd000ff8_13	fill in the blank 193db3fcd000ff8_14	%	fill in the blank 193db3fcd000ff8_15
Total			$fill in the blank 193db3fcd000ff8_16	fill in the blank 193db3fcd000ff8_17	%	$fill in the blank 193db3fcd000ff8_18

(Note: Difference due to rounding.)

b. Physical units method at split-off.

	Units	Percent	x	Joint Cost	=	Allocated Joint Costs
Studs	fill in the blank 193db3fcd000ff8_19	fill in the blank 193db3fcd000ff8_20%		$fill in the blank 193db3fcd000ff8_21		$fill in the blank 193db3fcd000ff8_22
Decorative pieces	fill in the blank 193db3fcd000ff8_23	fill in the blank 193db3fcd000ff8_24%		fill in the blank 193db3fcd000ff8_25		fill in the blank 193db3fcd000ff8_26
Posts	fill in the blank 193db3fcd000ff8_27	fill in the blank 193db3fcd000ff8_28%		fill in the blank 193db3fcd000ff8_29		fill in the blank 193db3fcd000ff8_30
Total	fill in the blank 193db3fcd000ff8_31					$fill in the blank 193db3fcd000ff8_32

c. Estimated net realizable value method. When required, round decimal values to four places before converting to a percentage. For example, .88349 would be rounded to .8835 and entered as "88.35" percent.

	Fully Processed Monthly Unit Output	Sales Price per Unit	Net Realizable Value	Percent of Value		Estimated Allocated Joint Costs
Studs	fill in the blank 193db3fcd000ff8_33	$fill in the blank 193db3fcd000ff8_34	$fill in the blank 193db3fcd000ff8_35	fill in the blank 193db3fcd000ff8_36	%	$fill in the blank 193db3fcd000ff8_37
Decorative pieces	fill in the blank 193db3fcd000ff8_38	fill in the blank 193db3fcd000ff8_39	fill in the blank 193db3fcd000ff8_40	fill in the blank 193db3fcd000ff8_41	%	fill in the blank 193db3fcd000ff8_42
Posts	fill in the blank 193db3fcd000ff8_43	fill in the blank 193db3fcd000ff8_44	fill in the blank 193db3fcd000ff8_45	fill in the blank 193db3fcd000ff8_46	%	fill in the blank 193db3fcd000ff8_47
Total			$fill in the blank 193db3fcd000ff8_48	fill in the blank 193db3fcd000ff8_49	%	$fill in the blank 193db3fcd000ff8_50

(Note: Difference due to rounding.)

2. Prepare an analysis for Sonimad Sawmill, Inc., to compare processing the decorative pieces further as it presently does, with selling the rough-cut product immediately at split-off.

Sonimad Sawmill, Inc.
Analysis Report
Monthly unit output	fill in the blank 05c8b805f004050_1
	fill in the blank 05c8b805f004050_3
	fill in the blank 05c8b805f004050_5
Final sales value	$fill in the blank 05c8b805f004050_6
	fill in the blank 05c8b805f004050_8
Differential revenue	$fill in the blank 05c8b805f004050_9
	fill in the blank 05c8b805f004050_11
Additional contribution from further processing	$fill in the blank 05c8b805f004050_12

Answer 1