Question

In: Physics

there is a sinusoidal message signal (f = 100 Hz). Make amplitude modulation with carrier frequency...

there is a sinusoidal message signal (f = 100 Hz).

Make amplitude modulation with carrier frequency of 10KHz. Use three different modulation depths / indices (0.2 /0.60/0.8).

Then demodulate this mixed signal (for these three cases) by try to get message signals. (need matlab codes and graphs)

Solutions

Expert Solution


Related Solutions

A carrier signal with unit amplitude and frequency fc1 = 50 kHz is modulated with a...
A carrier signal with unit amplitude and frequency fc1 = 50 kHz is modulated with a message signal ?1(?)=2cos(2??1?), where f1 = 15 kHz, to produce a DSB-SC signal. This DSB signal must be up-converted to a center frequency fc = 100 kHz. a. Determine the image frequency of the DSB signal. [2] b. An Upper-SSB signal with unit amplitude carrier at the image frequency calculated above also exists in the spectrum. The SSB signal is tone modulated with ?2(?)=4cos(2??2?),...
Please type at least 100 words: Compare AM (Amplitude Modulation) with FM (Frequency Modulation) in the...
Please type at least 100 words: Compare AM (Amplitude Modulation) with FM (Frequency Modulation) in the context of modulation techniques, frequency range, bandwidth requirements, complexity, noise, and hardware.
2. An AM radio station broadcasts a signal at a carrier frequency ωc, with an amplitude...
2. An AM radio station broadcasts a signal at a carrier frequency ωc, with an amplitude modulation frequency of ωm << ωc, E(t) = E0[1 + A sin(ωmt)] sin(ωct) Show that this is the sum of a wave at the carrier frequency, the lower sideband (ωL = ωc−ωm), and the upper (high) sideband (ωH = ωc + ωm). What total bandwidth is required if the radio station wants to broadcast music that contains modulation frequency components from 20 to 10,000...
1. Discuss what will happen to the modulation process of an amplitude modulation (AM) signal if...
1. Discuss what will happen to the modulation process of an amplitude modulation (AM) signal if the carrier signal level remains constant and the sideband signal level increases and justify your answer 2. A normal modulation usually has a modulation index ranges from 0 to 1 but in some rare cases, the modulation index can be greater than 1. Discuss what will happen to the output of the receiver if this situation happens.
7 If a carrier signal vc(t) = 10 sin (20000πt+π/2) volts is amplitude modulated by message...
7 If a carrier signal vc(t) = 10 sin (20000πt+π/2) volts is amplitude modulated by message vm(t) = 8sin(450πt+π/2), sketch the frequency plot for the resulting AM signal and calculate the transmission bandwidth. Write the expression for the AM signal. If the resulting AM signal is viewed on a CRO, what will be the values of Vmax and Vmin? Also sketch the AM signal in CRO and state whether the signal is under modulated / critically modulated / over modulated;...
1. Generate a sine wave with frequency 100 Hz. a. Sample the signal with a sampling...
1. Generate a sine wave with frequency 100 Hz. a. Sample the signal with a sampling frequency (i) 1000 Hz and (ii) 1050 Hz. b. For each frequency in Question 1(a), perform DFT for ONE (1) cycle and ONE and a HALF (1.5) cycles of the waveform. Comment on your observation.
A carrier signal of (500 kHz) is amplitude modulated to a depth of 75% by a...
A carrier signal of (500 kHz) is amplitude modulated to a depth of 75% by a single tone modulating signal of 18 KHz. The carrier amplitude is 800 Volts , and the antenna equivalent impedance is 70 Ohms. Calculate: 1- modulating wave voltage (Am) [volt] 2- The carrier power (Pc) [Watt] 3- The average output Power (Pt) [watt] 4- The percentage transmission efficiency [%] 5- The lower side band power (PLSB)
For a Double SideBand – Large Carrier (DSB-LC) Modulated Amplitude Modulator (AM) with a carrier frequency...
For a Double SideBand – Large Carrier (DSB-LC) Modulated Amplitude Modulator (AM) with a carrier frequency Fc = 1100kHz z and a maximum modulating signal frequency Fm (max) = 22kHz, determine: a. Frequency limits for the lower side bands (LSB) and upper (USB). b. Bandwidth c. The equation for the AM signal if the carrier has a Vrma voltage of 6V and the modulating signal has a Vrma voltage of 1V. Consider the fm(max) transmission. d. Lower (LSB) and upper...
1. a) A machine part is undergoing SHM with a frequency of 4.95 Hz and amplitude...
1. a) A machine part is undergoing SHM with a frequency of 4.95 Hz and amplitude 1.85 cm. How long does it take the part to go from x=0 to x=? 1.85 cm? bi) An object is undergoing SHM with period 0.930 s and amplitude 0.320 m. At t = 0, the object is at x = 0.320 mand is instantaneously at rest. Calculate the time it takes the object to go from x = 0.320 m, to x =...
Find out the amplitude ,frequency and phase displacement for given QPSK signal (a) 100 cos(25t+π/4). (b)...
Find out the amplitude ,frequency and phase displacement for given QPSK signal (a) 100 cos(25t+π/4). (b) 33.33 sin (350t+ 3π/4) .
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT