Question

In: Physics

1. Design a clock generator using a 555 timer with a frequency of 1 Hz (any...

1. Design a clock generator using a 555 timer with a frequency of 1 Hz (any duty cycle is OK). Use resistor values between 1k and 1M and use capacitor values available in lab (see table in “Pinouts.doc available on course Canvas site). Show your calculations for RA, RB, and C. Clearly show all formulas and calculations and state when you are arbitrarily picking a value. (DONE)

2. Select the nearest standard 5% resistor values to the values for RA and RB shown above. Include a printout of a table of standard 5% resistor values and highlight the ones selected. The table is available in “Pinouts.doc” or can be easily found online.

3. Recalculate f using these standard values chosen. Also calculate the values of T, TH, TL, and D. Show all calculations and the results. If you were already using standard values, simply state this fact.

I only need numbers 2 and 3 !!! I already have number 1 done but I thought it would be helpful to post it anyway.

Solutions

Expert Solution


Related Solutions

Design and simulate and fabrication a monostable multivibrators using 555 timer to produce a pulse width...
Design and simulate and fabrication a monostable multivibrators using 555 timer to produce a pulse width of 1 sec Calculate the freqency
We want to design a simple "four clock pulse" timer circuit. In addition to the clock...
We want to design a simple "four clock pulse" timer circuit. In addition to the clock input, the timer has a "Restart" input (R), three "data" outputs (ABC) which indicate the count, and one "beeper" output (D). The behavior of the circuit is as follows: Idle Mode The timer output is ABC=100 and the beeper is off (D=0) as long as R=0. If R=1 on any clock edge in this mode, the timer goes into the... Restart/Hold Mode The timer...
A clock pendulum oscillates at a frequency of 2.5 Hz . At t=0, it is released...
A clock pendulum oscillates at a frequency of 2.5 Hz . At t=0, it is released from rest starting at an angle of 11 ∘ to the vertical. Part A Ignoring friction, what will be the position (angle in radians) of the pendulum at t = 0.35 s ? Express your answer using two significant figures. θ = rad Part B Ignoring friction, what will be the position (angle in radians) of the pendulum at t = 1.60 s ?...
This is a atmega128 source to make a clock using the timer interrupt. I want to...
This is a atmega128 source to make a clock using the timer interrupt. I want to add source if i press switch (PIND==0x0FE&&PIND==0x0FD) then below program would be running . #include<io.h> int position=0,BJT[4]={0xFE,0xFD,0xFB,0xF7}; int number=0,segment[10]={0xC0,0xF9,0xA4,0xB0,0x99,0x92,0x82,0xF8,0x80,0x90}; int msec=0, sec=0, min=0; void main() { DDRA=0xFF; PORTA=0XFF; DDRB=0xFF; PORTB=0xFF; TCCR0=0x04; TIMSK=0x01; SREG=0x80; while(1){} } interrupt[TIM0_OVF]void timer0_ovf_isr() { TCNT0=0x06; PORTA=BJT[position]; if(position==0)number=sec%10; if(position==1)number=sec/10; if(position==2)number=min%10; if(postion==3)number=min/10; PORTB=segment[number]; position++; if(position>3)position=0; msec++; if(msec==1000) { msec=0; sec++; } if(sec==60) { sec=0; min++; } if(min==60)min=0; }
An ac generator with a frequency of 30.0 Hz and an rms voltage of 14.0 V...
An ac generator with a frequency of 30.0 Hz and an rms voltage of 14.0 V is connected to a 65.0 μF capacitor. 1. What is the maximum current in this circuit? 2. What is the current in the circuit when the voltage across the capacitor is 4.30 V and increasing? 3. What is the current in the circuit when the voltage across the capacitor is 4.30 V and decreasing?
Assume that you have a clock signal with frequency of 50 Hz, and you want to...
Assume that you have a clock signal with frequency of 50 Hz, and you want to divide this signal into a frequency of 1 Hz signal. The counter chips you must use are synchronous decade (MOD 10) counter chips 74160 and synchronous MOD 16 counter chips 74161. Please use the back side of this paper to draw your circuit diagram with all the details. You can use counter frequency division method to step down a higher frequency signal to a...
Frequency Divider: Use a count-for-50M counter and some glue logics to construct a 1 Hz clock...
Frequency Divider: Use a count-for-50M counter and some glue logics to construct a 1 Hz clock frequency. Construct a frequency divider of this kind. 2.1 Write the specification of the frequency divider. 2.2 Draw the block diagram of the frequency divider.
a. Design a broadband Butterworth bandpass filter with a lower cutoff frequency of 500 Hz and...
a. Design a broadband Butterworth bandpass filter with a lower cutoff frequency of 500 Hz and an upper cutoff frequency of 4500 Hz. The passband gain of the filter is 20 dB. The gain should be down at least 15 dB at 200 Hz and 11.25 kHz. Use 20 nF capacitors in the high-pass circuit and 10 k\Omega resistors in the low-pass circuit. b) Draw a circuit diagram of the filter and label all the components.
Design an active low pass filter with a corner frequency of 50 Hz and amplification of 10
 Design an active low pass filter with a corner frequency of 50 Hz and amplification of 10. Pick the values of the resistor and capacitor based on your own judgement to keep the cost reasonably low (simpler circuit design with less components is better).
Design a sine wave generator with adjustable frequency and amplitude. Show circuit diagram please!
Design a sine wave generator with adjustable frequency and amplitude. Show circuit diagram please!
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT