Question

In: Chemistry

We performed an experiment where first we prepared a buffer with a pH of about 5...

We performed an experiment where first we prepared a buffer with a pH of about 5 by adding a specific amount of sodium acetate and acetic acid and then prepared another buffer with the same pH by dissolving sodium acetate in water and adding HCl until the pH was 5. Then when we slowly added HCl/NaOH to half of each solution we calculated that the buffer capacity of the second solution was slightly better. Why might that be? Or should it be the other way around? If so why?

Solutions

Expert Solution

If the concentrations of a solution of a weak acid and its conjugate base are reasonably high, then the solution is resistant to changes in hydrogen ion concentration. These solutions are known as buffers. It is possible to calculate how the pH of the solution will change in response to the addition of an acid or a base to a buffer solution.

Calculating Changes in a Buffer Solution, Example 1:

A solution is 0.050 M in acetic acid (HC2H3O2) and 0.050 M NaC2H3O2. Calculate the change in pH when 0.001 mole of hydrochloric acid (HCl) is added to a liter of solution, assuming that the volume increase upon adding the HCl is negligible. Compare this to the pH if the same amount of HCl is added to a liter of pure water.

Step 1:

HC2H3O2(aq)⇋H+(aq)+C2H3O−2(aq)

Recall that sodium acetate, NaC2H3O2, dissociates into its component ions, Na+ and C2H3O2- (the acetate ion) upon dissolution in water. Therefore, the solution will contain both acetic acid and acetate ions.

Before adding HCl, the acetic acid equilibrium constant is:

Ka=[H+][C2H3O2−][HC2H3O2]=x(0.050)(0.050)

(assuming that x is small compared to 0.050 M in the equilibrium concentrations)

Therefore:

x=[H+]=Ka=1.76×10−5M

pH=pKa=4.75

In this example, ignoring the x in the [C2H3O2-] and [HC2H3O2] terms was justified because the value is small compared to 0.050.

Step 2:

The added protons from HCl combine with the acetate ions to form more acetic acid:

C2H3O−2+H+(fromHCl)→HC2H3O2

Since all of the H+ will be consumed, the new concentrations will be [HC2H3O2]=0.051M and [C2H3O−2]=0.049M before the new equilibrium is to be established. Then, we consider the equilibrium conentrations for the dissociation of acetic acid, as in Step 1:

HC2H3O2(aq)⇋H+(aq)+C2H3O−2(aq)

we have,

Ka=x(0.049)(0.051)

x=[H+]=(1.76×10−5)0.0510.049=1.83×10−5M

pH=−log([H+])=4.74

In the presence of the acetic acid-acetate buffer system, the pH only drops from 4.75 to 4.74 upon addition of 0.001 mol of strong acid HCl, a difference of only 0.01 pH unit.

Step 3:

Adding 0.001 M HCl to pure water, the pH is:

pH=−log([H+])=3.00

In the absence of HC2H3O2 and C2H3O2-, the same concentration of HCl would produce a pH of 3.00.

Calculating Changes in a Buffer Solution, Example 2:

A formic acid buffer is prepared with 0.010 M each of formic acid (HCOOH) and sodium formate (NaCOOH). The Ka for formic acid is 1.8 x 10-4. What is the pH of the solution? What is the pH if 0.0020 M of solid sodium hydroxide (NaOH) is added to a liter of buffer? What would be the pH of the sodium hydroxide solution without the buffer? What would the pH have been after adding sodium hydroxide if the buffer concentrations had been 0.10 M instead of 0.010 M?

Step 1:

Solving for the buffer pH:

HCOOH⇋H++HCOO−

Assuming x is negligible, the Ka expression looks like:

Ka=x(0.010)(0.010)

1.8 x 10-4 = x = [H+]

pH = -log [H+] = 3.74

Buffer: pH = 3.74

Step 2:

Solving for the buffer pH after 0.0020 M NaOH has been added:

OH−+HCOOH→H2O+HCOO−

The concentration of HCOOH would change from 0.010 M to 0.0080 M and the concentration of HCOO- would change from 0.010 M to 0.0120 M.

Ka=x(0.0120)(0.0080)

After adding NaOH, solving for x=[H+] and then calculating the pH = 3.92. The pH went up from 3.74 to 3.92 upon addition of 0.002 M of NaOH.

Step 3:

Solving for the pH of a 0.0020 M solution of NaOH:

pOH = -log (0.0020)

pOH = 2.70

pH = 14 - pOH

pH = 11.30

Without buffer: pH = 11.30

Step 4:

Solving for the pH of the buffer solution if 0.1000 M solutions of the weak acid and its conjugate base had been used and the same amount of NaOH had been added:

The concentration of HCOOH would change from 0.1000 M to 0.0980 M and the concentration of HCOO- would change from 0.1000 M to 0.1020 M.

Ka=x(0.1020)(0.0980)

pH if 0.1000 M concentrations had been used = 3.77

This shows the dramatic effect of the formic acid-formate buffer in keeping the solution acidic in spite of the added base. It also shows the importance of using high buffer component concentrations so that the buffering capacity of the solution is not exceeded.


Related Solutions

We performed a final experiment where we determined the tightness of DNA packaging for this gene...
We performed a final experiment where we determined the tightness of DNA packaging for this gene in wild-type toe cells, and in toe cells in which the Talon enhancer had been mutated as described for constructs g-k. In this experiment we isolated chromatin and determined if an enzyme cuts in the gene very well or very poorly, depending on how tightly packed the DNA is at the site of cutting. c. Suggest why the ability of an enzyme to cut...
Part A: What is the pH of a buffer prepared by adding 0.405 mol of the...
Part A: What is the pH of a buffer prepared by adding 0.405 mol of the weak acid HA to 0.608 mol of NaA in 2.00 L of solution? The dissociation constant Ka of HA is 5.66×10−7. Part B: What is the pH after 0.150 mol of HCl is added to the buffer from Part A? Assume no volume change on the addition of the acid. Part C: What is the pH after 0.195 mol of NaOH is added to...
What is the pH of a buffer that is prepared by mixing 30.0 mL of 1.0...
What is the pH of a buffer that is prepared by mixing 30.0 mL of 1.0 M HF and 20.0 mL of 2.0 M KF? (Ka for HF 7.2 x 10−4) What is the pH of a solution that contains 0.40 M CH3COOH and 0.30 M CH3COONa at 25°C (Ka=1.8 x 10−5)?
What is the pH of a buffer that is prepared by mixing 30.0 mL of 1.0...
What is the pH of a buffer that is prepared by mixing 30.0 mL of 1.0 M HF and 20.0 mL of 2.0 M KF? (K a a for HF 7.2 x 10 −4 )
PART A: What is the pH of a buffer prepared by adding 0.506 mol of the...
PART A: What is the pH of a buffer prepared by adding 0.506 mol of the weak acid HA to 0.305 mol of NaA in 2.00 L of solution? The dissociation constant Ka of HA is 5.66×10−7? PART B: What is the pH after 0.150 mol of HCl is added to the buffer from Part A? Assume no volume change on the addition of the acid. Express the pH numerically to three decimal places. PART C: What is the pH...
Part A What is the pH of a buffer prepared by adding 0.607 mol of the...
Part A What is the pH of a buffer prepared by adding 0.607 mol of the weak acid HA to 0.406 mol of NaA in 2.00 L of solution? The dissociation constant Ka of HA is 5.66×10−7. Express the pH numerically to three decimal places. Answer: pH = 6.072 Part C What is the pH after 0.195 mol of NaOH is added to the buffer from Part A? Assume no volume change on the addition of the base. Express the...
A- What is the pH of a buffer prepared by adding 0.405 mol of the weak...
A- What is the pH of a buffer prepared by adding 0.405 mol of the weak acid HA to 0.305 mol of NaA in 2.00 L of solution? The dissociation constant Ka of HA is 5.66×10−7. Express the pH numerically to three decimal places. B- What is the pH after 0.150 mol of HCl is added to the buffer from Part A? Assume no volume change on the addition of the acid. Express the pH numerically to three decimal places....
a) What is the pH of a buffer solution prepared by mixing 120 mL of a...
a) What is the pH of a buffer solution prepared by mixing 120 mL of a 0.435 M CH3CO2H with 50 mL of a .286 M CH3CO2Na solution? CH3CO2H Ka = 1.75 x 10-5 b) What is the resulting pH if we add 10.2 mL of a .513 M HCl solution to this buffer? Does the pH make sense? Why/why not? c) What is the resulting pH if we add 3.56 mL of a 0.420 M NaOH solution to the...
Calculated the PH of the prepared buffer of 0.50 ml of 1.0M of NaOH is added...
Calculated the PH of the prepared buffer of 0.50 ml of 1.0M of NaOH is added to 50mL of the buffer. Required Buffer (Volume, Concentration, pH) 50 mL of 0.05 M pH 12.0 buffer Chosen Acid/ Conjugate Base Pair: Na2HPO4 / Na3PO4 Amount of Acid: 0.2498 g Amount of Conjugate Base: 0.1227 g Measured PH:10.92
1. Determine the pH of the buffer solution that is prepared by mixing 259 mL of...
1. Determine the pH of the buffer solution that is prepared by mixing 259 mL of 0.0983 M BIS−TRIS propane−H (C11H27N2O6+ ) to 855 mL of 0.0729 M BIS-TRIS_propane (C11H26N2O6) ). Assume the 5% approximation is valid. Report your answer to 2 decimal places. The pKa of BIS−TRIS propane−H is 9.10. Submit Answer Tries 0/3 2. Determine the pH of the BIS−TRIS propane−H/BIS−TRIS propane buffer solution after the addition of 25.2 mL of 0.643 M solution of rubidium hydroxide to...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT