Question

In: Physics

when performing an anolog galvanometer experiment, we need to graph power supply voltage vs analog galvanomete...

when performing an anolog galvanometer experiment, we need to graph power supply voltage vs analog galvanomete voltage, but the galvanometer units are in mA. How do we covert to volts.

Solutions

Expert Solution

sorry if images are get shuffled....please ask if i miss something...plzz dont downvote....ask first i shal be thankful to you.


Related Solutions

An AC power supply produces a maximum voltage ΔVmax = 88 V. This power supply is...
An AC power supply produces a maximum voltage ΔVmax = 88 V. This power supply is connected to a resistor R = 27.0 Ω, and the current and resistor voltage are measured with an ideal AC ammeter and voltmeter as shown in the figure below. An ideal ammeter has zero resistance, and an ideal voltmeter has infinite resistance. (a) What is the reading on the ammeter? A (b) What is the reading on the voltmeter? V
A manufacturer is interested in the output voltage of a power supply used in a PC....
A manufacturer is interested in the output voltage of a power supply used in a PC. Output voltage is assumed to be normally distributed, with standard deviation 0.25 V, and the manufacturer wishes to test H0: μ = 9 V against H1: μ ≠ 9 V with a sample of n = 10 units. (a) The critical region is defined as , find the type I error probability α. (b) Find the power of the test for detecting a true...
A manufacturer is interested in the output voltage of a power supply used in a PC....
A manufacturer is interested in the output voltage of a power supply used in a PC. Output voltage is assumed to be normally distributed, with standard deviation 0.25 volt. The manufacturer wishes to test H0: μ=5 volts against H1: μ≠5 volts using α=0.10. Suppose a sample size of 8 power supply units is used and you are interested in computing the probability the test will fail to detect a true mean output voltage of 5.1 volts. What is the appropriate...
Problem 4. A high-voltage power supply should have a nominal output voltage of 350 V. A...
Problem 4. A high-voltage power supply should have a nominal output voltage of 350 V. A sample of four units is selected each day and tested for process-control purposes. The data (see sheet Problem4 in Homework 4.xlsx) give the difference between the observed reading on each unit and the nominal voltage times ten; that is, ?? = (observed voltage on unit ? - 350)*10 (a) Set up ?̅ and ? charts on this process. Is the process in statistical control?...
A high-level voltage power supply should have a nominal output voltage of 350 V. A sample...
A high-level voltage power supply should have a nominal output voltage of 350 V. A sample of four units is selected each day and tested for process-control purposes. The data (20 days, 1 sample/day) shown in the table below give the difference between the observed reading on each unit and the nominal voltage times ten; that is, xi = (observed voltage on unit 350)*10. Voltage Data Voltage Data Sample # xi Sample # xi 1 6 11 8 1 9...
For a power supply with full wave bridge rectifier, input voltage is 230 V and required...
For a power supply with full wave bridge rectifier, input voltage is 230 V and required output voltage is 12 V DC Load resistance is of 100 . Determine output rms voltage, dc current, rms current, power, ac power, efficiency of the rectifier, form factor, ripple factor, transformer utilization factor, and size of the transformer Draw complete diagram of the supply circuit
A quality control engineer wishes to estimate the mean output voltage of a DC power supply...
A quality control engineer wishes to estimate the mean output voltage of a DC power supply for different loads. The engineer measures output voltage when the supply is connected to 11 different loads and computes a mean 98.4 V and standard deviation 7 V. Assume that the output voltages follow a normal distribution. (a) Construct and interpret the 99.9% confidence interval. (b) Construct and interpret the 90% prediction interval.
A power supply produces voltage described as V= 100sin(60t). what is the average value of this...
A power supply produces voltage described as V= 100sin(60t). what is the average value of this voltage and what is the average voltage squared? The average voltage is supposed to be 0V and then the avg voltage squared is supposed to be 5000 V^2 which makes zero sense to me. Thanks!
The output voltage of a power supply unit has an unknown distribution. Using a sample size...
The output voltage of a power supply unit has an unknown distribution. Using a sample size of 36, sixteen samples are taken with the following sample-mean values: 10.35 V, 9.30 V, 10.00 V, 9.96 V, 11.65 V, 12.00 V, 11.25 V, 9.58 V, 11.54 V, 9.95 V, 10.28 V, 8.37 V, 10.44 V, 9.25 V 9.38 V and 10.85 V. Let µ and σ2 denote the mean and the variance of the output voltage of the power supply unit. (a)...
A collector-modulated power has a supply voltage of 48V and an average collector current of 600...
A collector-modulated power has a supply voltage of 48V and an average collector current of 600 mA. Determine: a) the input power to the transmitter? b) the modulating signal power needed to produce 100% modulation? 2) …. receivers convert all incoming signals to a lower, fixed frequency. 3) List all the frequencies that emerge from a mixer that is fed with an incoming frequency of 107.1 MHz and another frequency of 96.4 MHz What is the Image Frequency that results...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT