Question
In: Mechanical Engineering
Design a double-dwell cam to move a follower from 0 to 2.5 in. in 60°, dwell...
Design a double-dwell cam to move a follower from 0 to 2.5 in.
in 60°, dwell for 120°, fall 2.5 in. in 30°, and dwell for the
remainder. The total cycle must take 4 sec. Size the cam for a
1-in. radius roller follower considering pressure angle and radius
of curvature. Use eccentricity only if necessary to balance these
functions. Plot both these functions. Draw the cam profile. Repeat
this for a flat-faced follower. Which one would you use?
Solutions
samet mamat answered 1 month agoRelated Solutions
Design a double-dwell cam to move a follower from 0 to 2.5 in. in 60°, dwell...
Design a double-dwell cam to move a follower from 0 to 2.5 in.
in 60°, dwell for 120°, fall 2.5 in. in 30°, and dwell for the
remainder. The total cycle must take 4 sec. Size the cam for a
1-in. radius roller follower considering pressure angle and radius
of curvature. Use eccentricity only if necessary to balance these
functions. Plot both these functions. Draw the cam profile. Repeat
this for a flat-faced follower. Which one would you use?
Solve by hand /No Dynacam Design a single dwell cam to move a follower, dwell for...
Solve by hand /No Dynacam
Design a single dwell cam to move a follower, dwell for 120 deg,
rise from 0 to 3 inches in 100 deg and fall 3 inches in 140 deg.
the total cycle must take 2 sec. choose suitable function for rise
and fall to minimize acceleration. Plot SVAJ diagram
USING DYNACAM determine the polynomial equation for a single dwell cam to move a follower as...
USING DYNACAM determine the polynomial equation for a single
dwell cam to move a follower as follows
Dwell 0 deg to 100 deg
Rise .625 inches from 100 deg to 200 deg
Fall .625 inches from 200 deg to 360 deg
minimize velocity
DETERMINE THE NUMBER OF BOUNDARY CONDITIONS, THE CONSTANTS, AND
THE POLYNOMIAL EQUATIONS FOR THE SVAJ DIAGRAMS
solve using Dynacam and write outputted polynomial equations Design a single dwell cam to move a...
solve using Dynacam and write outputted polynomial equations
Design a single dwell cam to move a follower dwell from 0 to 100
deg, rise 3 inches in100 deg and fall 3 inches in 160 deg. the
total cycle must take 2 sec. choose suitable functions for rise and
fall to minimize acceleration. Plot SVAJ diagram
Design a cam for a rise-return-dwell (RRD) application using the fourth order polynomial. The position, velocity,...
Design a cam for a rise-return-dwell (RRD) application using the
fourth order polynomial. The position, velocity, and acceleration
should be zero at the beginning of the rise h, and the velocity
should be zero at the end of the rise.
Plot s, v, a, and j profiles for BOTH fourth and fifth order
polynomials using EXCEL.
(Note: this is to all be done by hand in regards to the fourth
and fifth order polynomial. Only Excel can be used for...
Use Excel to generate a column of x values from 0 to 2.5 in steps of...
Use Excel to generate a column of x values from 0 to 2.5 in
steps of 0.05 (that means your column must have numbers like 0,
0.05, 0.1, 0.15, . . . , 2.5).
Plot the PDF f(x) on your computer screen for the different
values of x mentioned above for the following distributions.
(a) Uniform (use A = 0 and B = 2.5)
(b) Exponential (use mean = 2)
(c) Gamma (use parameters 1.7 and 1.2)
(d) Normal (use...
Design a system to move 100 gpm of water from a river with surface water elevation...
Design a system to move 100 gpm of water from a river with
surface water elevation of 201.35 ft msl to a tank with surface
water elevation = 246.55 ft msl. The tank is pressurized; the air
pressure in the tank is 60 psig. The total length of pipe is 125 ft
with 6 standard elbows all made of Sch 40 steel pipe. Your design
should specify the nominal diameter of pipe (use only commercially
available sizes) and the power...
Evaluate the double integral explicitly by reversing the order of integration:? Integral from 0 to 8...
Evaluate the double integral explicitly by reversing the order
of integration:? Integral from 0 to 8 and integral from (sub3
square root of y) to 2 ex dxdy
A pipe is carrying liquid at 60 degrees C, that fluctuates in pressure from 0 to...
A pipe is carrying liquid at 60 degrees C, that fluctuates in
pressure from 0 to 60,000 kPa (non-capped). The inside diameter of
the pipe is 20 mm and the wall thickness is 1 mm and is made out of
1095 carbon steel, has a yield strength of 813 MPa and an ultimate
tensile strength of 1260 MPa. Using the "Modified-Goodman" failure
criteria and a reliability factor of 99%, determine the number of
cycles till failure on the inside wall....
Design and implement a sequential circuit that counts from 0-3 in a repeating cycle with two...
Design and implement a sequential circuit that counts from 0-3
in a repeating cycle with two inputs: step and reset. If the step
input is 1 the count progresses to the next value, if 0 you stay at
the current value. If the reset input is 1 the count returns to 0,
if 0 it has no effect. If both step and reset are 1, reset takes
precedence.
Use J-K flip flops in your design and follow the design process...
ADVERTISEMENT
ADVERTISEMENT
Latest Questions
- Suppose that many stocks are traded in the market and that it is possible to borrow...
- Which 2 UML diagrams would you say are the most valuable in terms of understanding the...
- A) Modify the ArrayOfCircles.java file such that it implements the missing methods in the given SimpleListInterface....
- The development of the world wide web has led to a variety of Top Level Domains...
- What specifically do you need to be aware of when you are using or referring to...
- Market Efficiency – Write a paper about market efficiency. How is the concept of market efficiency...
- Select two PaaS cloud service providers and Analyze each service provider’s capability to provide big-data cloud services...
ADVERTISEMENT