Design a double-dwell cam to move a follower from 0 to 2.5 in. in 60°, dwell...

Design a double-dwell cam to move a follower from 0 to 2.5 in. in 60°, dwell for 120°, fall 2.5 in. in 30°, and dwell for the remainder. The total cycle must take 4 sec. Size the cam for a 1-in. radius roller follower considering pressure angle and radius of curvature. Use eccentricity only if necessary to balance these functions. Plot both these functions. Draw the cam profile. Repeat this for a flat-faced follower. Which one would you use?

Solutions

Expert Solution

samet mamat answered 1 year ago

Next > < Previous

Related Solutions

Solve by hand /No Dynacam Design a single dwell cam to move a follower, dwell for...

Solve by hand /No Dynacam Design a single dwell cam to move a follower, dwell for 120 deg, rise from 0 to 3 inches in 100 deg and fall 3 inches in 140 deg. the total cycle must take 2 sec. choose suitable function for rise and fall to minimize acceleration. Plot SVAJ diagram

USING DYNACAM determine the polynomial equation for a single dwell cam to move a follower as...

USING DYNACAM determine the polynomial equation for a single dwell cam to move a follower as follows Dwell 0 deg to 100 deg Rise .625 inches from 100 deg to 200 deg Fall .625 inches from 200 deg to 360 deg minimize velocity DETERMINE THE NUMBER OF BOUNDARY CONDITIONS, THE CONSTANTS, AND THE POLYNOMIAL EQUATIONS FOR THE SVAJ DIAGRAMS

solve using Dynacam and write outputted polynomial equations Design a single dwell cam to move a...

solve using Dynacam and write outputted polynomial equations Design a single dwell cam to move a follower dwell from 0 to 100 deg, rise 3 inches in100 deg and fall 3 inches in 160 deg. the total cycle must take 2 sec. choose suitable functions for rise and fall to minimize acceleration. Plot SVAJ diagram

Design a cam for a rise-return-dwell (RRD) application using the fourth order polynomial. The position, velocity,...

Design a cam for a rise-return-dwell (RRD) application using the fourth order polynomial. The position, velocity, and acceleration should be zero at the beginning of the rise h, and the velocity should be zero at the end of the rise. Plot s, v, a, and j profiles for BOTH fourth and fifth order polynomials using EXCEL. (Note: this is to all be done by hand in regards to the fourth and fifth order polynomial. Only Excel can be used for...

Use Excel to generate a column of x values from 0 to 2.5 in steps of...

Use Excel to generate a column of x values from 0 to 2.5 in steps of 0.05 (that means your column must have numbers like 0, 0.05, 0.1, 0.15, . . . , 2.5). Plot the PDF f(x) on your computer screen for the different values of x mentioned above for the following distributions. (a) Uniform (use A = 0 and B = 2.5) (b) Exponential (use mean = 2) (c) Gamma (use parameters 1.7 and 1.2) (d) Normal (use...

Design a system to move 100 gpm of water from a river with surface water elevation...

Design a system to move 100 gpm of water from a river with surface water elevation of 201.35 ft msl to a tank with surface water elevation = 246.55 ft msl. The tank is pressurized; the air pressure in the tank is 60 psig. The total length of pipe is 125 ft with 6 standard elbows all made of Sch 40 steel pipe. Your design should specify the nominal diameter of pipe (use only commercially available sizes) and the power...

Evaluate the double integral explicitly by reversing the order of integration:? Integral from 0 to 8...

Evaluate the double integral explicitly by reversing the order of integration:? Integral from 0 to 8 and integral from (sub3 square root of y) to 2 ex dxdy

A pipe is carrying liquid at 60 degrees C, that fluctuates in pressure from 0 to...

A pipe is carrying liquid at 60 degrees C, that fluctuates in pressure from 0 to 60,000 kPa (non-capped). The inside diameter of the pipe is 20 mm and the wall thickness is 1 mm and is made out of 1095 carbon steel, has a yield strength of 813 MPa and an ultimate tensile strength of 1260 MPa. Using the "Modified-Goodman" failure criteria and a reliability factor of 99%, determine the number of cycles till failure on the inside wall....

Design and implement a sequential circuit that counts from 0-3 in a repeating cycle with two...

Design and implement a sequential circuit that counts from 0-3 in a repeating cycle with two inputs: step and reset. If the step input is 1 the count progresses to the next value, if 0 you stay at the current value. If the reset input is 1 the count returns to 0, if 0 it has no effect. If both step and reset are 1, reset takes precedence. Use J-K flip flops in your design and follow the design process...

Question 3: A)Design a BCD counter. -The circuit counts from 0 to 9, then resets back...

Question 3: A)Design a BCD counter. -The circuit counts from 0 to 9, then resets back to 0 to restart the counting sequence. -The circuit has one input run/stop. If the input is 1, the eounter will count. If the input is 0, the counter will freeze in its current location until the input is set to 1 again. -The circuit has one output. It becomes 1 when the counter completes a cycle and starts the next one. Otherwise, that...

Subjects