You build a transformer with 100 turns of wire on side 1, and 500 turns on...

You build a transformer with 100 turns of wire on side 1, and 500 turns on side 2. A) If you put a voltage of 100 V (AC) on side 1, what voltage would you get on side 2? B) If you put a voltage of 100 V (AC) on side 1 with a current of 1 Amp (AC), what current would you get on side 2? C) If you put 100 V of DC voltage on side 1, what voltage would you get on side 2?

Expert Solution

summary : This problem is based on using transformer turns ratio . For the convenience of understand represented side 1 and 2 as primary side and secondary side

we give DC as input on primary. its acts a short circuit in secondary due to change rate of current with respect to time is zero hence di/dt is zero and so transformer will burn or damage

genius_generous answered 2 years ago

1. An ideal transformer has a primary with 25 turns and secondary with 15 turns. The...

1. An ideal transformer has a primary with 25 turns and secondary with 15 turns. The load resistor is 24 ? and the source voltage is 85 Vrms.What is the rms electric potential across the 24 ? load resistor? Answer in units of Vrms 2. A transformer consists of two coils of wire wound on a common toroidal iron core. The mutual inductance of the pair is 483 mH and the current in the first coil decreases from 29 A...

A square single loop of wire 4.00 cm on a side with 875 turns lies in...

A square single loop of wire 4.00 cm on a side with 875 turns lies in the xy-plane. The loop is in a uniform magnetic field that changes at a steady rate from B⃗ =(0.200T)i^+(0.150T)k^B→=(0.200T)i^+(0.150T)k^ at t = 0 to B⃗ =(0.300T)i^+(−0.200T)k^ B→=(0.300T)i^+(−0.200T)k^ at t=3.00s. At the time t=2.00s, a) find the magnitude of the induced emf in the coil. b) Find the direction of the induced current in the coil as seen from a point on the +z-axis.

The secondary of a 500kVA, 4400/500 V, 50Hz, single-phase transformer has 500 turns. A) determine emf...

The secondary of a 500kVA, 4400/500 V, 50Hz, single-phase transformer has 500 turns. A) determine emf per unit. B) primary turns. C) secondary full load current D) maximum flux E) gross cross-sectional area of the core for flux density of 1.2 tesla F) if the core is square cross-section find the width of the limb

A current transformer rated 500/5 A, 20 VA, 50 Hz has a turns ratio of 1:99....

A current transformer rated 500/5 A, 20 VA, 50 Hz has a turns ratio of 1:99. Its resistance aand leakage reluctance of the secondary winding are 0.4 Ω and 0.35 Ω respectively. At rated non-inductive burden, the inphase and quadrature components of the exciting mmf are 6 AT and 8 AT respectively. Determine the current and phase angle error.

A square coil of thin wire with 4 turns and side-length 3 cm sits inside an...

A square coil of thin wire with 4 turns and side-length 3 cm sits inside an ideal solenoid. The axis of the solenoid is along +k, but the axis of the coil is tilted at a fixed unknown angle θ from the +z-axis. The solenoid has n = 5000 turns/meter, and carries current I(t) = 5t3– 4t2+ t + 5 [units of Amperes with t given in seconds] counterclockwise. The wire of the coil has cross-sectional area A = 50 μm2, and the...

An ideal transformer has 50 turns in its primary and 250 turns in its secondary. 12...

An ideal transformer has 50 turns in its primary and 250 turns in its secondary. 12 V ac is connected to the primary. Find: a. The voltage ac available at the secondary. b. Current in the 10 ohms device connected to the secondary. c. Power supplied to the primary. d. Power supplied to the secondary.

An ideal transformer has 50 turns in its primary (input) and 450 turns in its secondary...

An ideal transformer has 50 turns in its primary (input) and 450 turns in its secondary (output). 10.0-V ac is connected to the primary (input). a) What is the voltage on the secondary (output)? b) What is the secondary (output) current if a 10.0- resistor is connected to the secondary (output)? c) What is the power supplied to the primary (input)?

A transformer is plugged into a regular U.S. Wall outlet. There are 200 turns in the...

A transformer is plugged into a regular U.S. Wall outlet. There are 200 turns in the primary coil, and 4000 turns in the secondary coil. A) What is the rms voltage and peak voltage on the secondary coil? (two answers) B) An electrical worker accidently grabs one of the loops of the secondary coil with a single bare hand. Her other hand is in midair, and both of his shoes are firmly on the ground. The resistance in her body...

1 The line to ground voltages on the high voltage side of a step-up transformer are...

1 The line to ground voltages on the high voltage side of a step-up transformer are 100 kV, 33 kV and 38 kV on phases a, b and c respectively. The voltage of phase a leads that of phase b by 100° and lags that of phase c by 176.5°. Determine the symmetrical negative phase sequence component of phase a. 2. A 3-phase, 4-wire system supplies loads which are unequally distributed in the three phases. An analysis of the current...

A 10.0-cm side square loop is fashioned from a single 4.00-m long, 100-g wire. One side...

A 10.0-cm side square loop is fashioned from a single 4.00-m long, 100-g wire. One side of the loop is attached to a horizontal, frictionless axle. The loop is suspended in a region with a uniform 10.0-mT magnetic field oriented vertically. (a) What angle does the loop make with the vertical when it carries a current of 3.40 A? (b) What magnetic torque acts on the loop?

Question