Question

In: Physics

The wạlls of ạn ice chest ạre mạde of 2.00-mm-thick insulạtion hạving ạ thermạl conductivity 0.00300...

The wạlls of ạn ice chest ạre mạde of 2.00-mm-thick insulạtion hạving ạ thermạl conductivity 0.00300 W/m∙K. The totạl surfạce ạreạ of the ice chest is 1.20 m2. The temperạture of the outside surfạce of the chest is 20.0 °C. The lạtent heạt of fusion of wạter is 334 kJ/kg.

How mạny hours (time) does it tạke to melt 4.00 kg of ice plạced inside the ice chest?

Solutions

Expert Solution


Related Solutions

A 0.313-m-thick sheet of ice covers a lake. The air temperature at the ice surface is...
A 0.313-m-thick sheet of ice covers a lake. The air temperature at the ice surface is -15.9 °C. In 4.70 minutes, the ice thickens by a small amount. Assume that no heat flows from the ground below into the water and that the added ice is very thin compared to 0.313 m. Calculate the number of millimeters by which the ice thickens. Do not enter unit.
A 0.294-m-thick sheet of ice covers a lake. The air temperature at the ice surface is...
A 0.294-m-thick sheet of ice covers a lake. The air temperature at the ice surface is -17.7 °C. In 3.00 minutes, the ice thickens by a small amount. Assume that no heat flows from the ground below into the water and that the added ice is very thin compared to 0.294 m. Calculate the number of millimeters by which the ice thickens. Do not enter unit.
A low-carbon steel plate is 270 mm wide and 25 mm thick. It is reduced in...
A low-carbon steel plate is 270 mm wide and 25 mm thick. It is reduced in one pass in a two‑high rolling mill to a thickness of 20 mm. Roll radius = 300 mm, and roll speed = 30 m/min. Strength coefficient = 500 MPa, and strain hardening exponent = 0.25. Determine (a) roll force, N (b) roll torque, N-m and (c) power required to perform the operation kW.
In a slab of material 0.25 m thick and having a thermal conductivity of 45 W/mK,...
In a slab of material 0.25 m thick and having a thermal conductivity of 45 W/mK, the temperature °C at x under steady state is given by T = 100 + 200x – 400x2 when x is measured from one face in m. Determine the heat flow at x = 0, x = 0.125 and x = 0.25 m and also the temperatures and temperature gradients at these planes. If the difference in heat flow at these sections is due...
A cast iron water pipe of 500 mm inside diameter and 20 mm thick, is supported...
A cast iron water pipe of 500 mm inside diameter and 20 mm thick, is supported over a span of 10 meters. Find the maximum bending stress in the pipe metal, when the pipe is running full. Take density of cast iron = 70.6 kN/m3 and water = 9.8 kN/m3
A Copper plate that is 588mm wide and 48 mm thick is to be reduced in...
A Copper plate that is 588mm wide and 48 mm thick is to be reduced in a single pass in a two high rolling mill by using a 321mm diameter roll. The coefficient of friction at roll workpiece interface is  0.14 and the roll rotates at 107rpm. The rolling process is performed above the recrystallization temperature of the material and the width of the plate does not change during this operation. What is the minimum final thickness (mm) possible
A plank 2.00 cm thick and 14.3 cm wide is firmly attached to the railing of...
A plank 2.00 cm thick and 14.3 cm wide is firmly attached to the railing of a ship by clamps so that the rest of the board extends 2.00 m horizontally over the sea below. A man of mass 95.3 kg is forced to stand on the very end. If the end of the board drops by 4.90 cm because of the man's weight, find the shear modulus of the wood.
500 mm thick square footing is to be placed at a depth of 0.5 m in...
500 mm thick square footing is to be placed at a depth of 0.5 m in a clayey sand where c¢ = 10 kPa, f¢ = 34°, g = 19.0 kN/m3. The column load to be applied on the footing is 2000 kN. What should be the width of the footing?
500 mm thick square footing is to be placed at a depth of 0.5 m in...
500 mm thick square footing is to be placed at a depth of 0.5 m in a clayey sand where c¢ = 10 kPa, f¢ = 34°, g = 19.0 kN/m3. The column load to be applied on the footing is 2000 kN. What should be the width of the footing? please show each steps with how you solved to obtain value of B
500 mm thick square footing is to be placed at a depth of 0.5 m in...
500 mm thick square footing is to be placed at a depth of 0.5 m in a clayey sand where c¢ = 10 kPa, f¢ = 34°, g = 19.0 kN/m3. The column load to be applied on the footing is 2000 kN. What should be the width of the footing?
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT