A low-carbon steel plate is 270 mm wide and 25 mm thick. It is reduced in...

A low-carbon steel plate is 270 mm wide and 25 mm thick. It is reduced in one pass in a two‑high rolling mill to a thickness of 20 mm. Roll radius = 300 mm, and roll speed = 30 m/min. Strength coefficient = 500 MPa, and strain hardening exponent = 0.25. Determine (a) roll force, N (b) roll torque, N-m and (c) power required to perform the operation kW.

Expert Solution

Roll Force = 2874644 N

Roll Torque = 55767 N-m

Power Required = 186 KW

Hope it helps.

samet mamat answered 2 years ago

A Copper plate that is 588mm wide and 48 mm thick is to be reduced in...

A Copper plate that is 588mm wide and 48 mm thick is to be reduced in a single pass in a two high rolling mill by using a 321mm diameter roll. The coefficient of friction at roll workpiece interface is 0.14 and the roll rotates at 107rpm. The rolling process is performed above the recrystallization temperature of the material and the width of the plate does not change during this operation. What is the minimum final thickness (mm) possible

An AISI 1010 carbon steel plate of 1 by 1 m size and of 6 mm...

An AISI 1010 carbon steel plate of 1 by 1 m size and of 6 mm thickness is hung vertically after a heat treatment to 300°C uniform temperature. It is cooled by ambient air at 20°C flowing parallel to the plate in transverse direction. a) Considering both forced and natural convection, for 8 m/s transverse air velocity, determine the rate of heat transfer from the plate and the corresponding instantaneous rate of change of the plate temperature. b) For the...

Using the Faraday equation. What current and time are needed to plate a 1 mm thick...

Using the Faraday equation. What current and time are needed to plate a 1 mm thick layer of copper onto an object with a surface area of 0.1m2 ? The density of copper is 8940 kg/m3 , its atomic weight is M = 63.5 kg/kmol and copper ions have a valence of z = 2.

A Brinell hardness tester is used to determine the hardness of 1/2" thick steel plate. The...

A Brinell hardness tester is used to determine the hardness of 1/2" thick steel plate. The specifications for the steel require that the steel have a tensile strength between 125 ksi and 150 ksi. A 3000 kg load is used for the test. A. Calculate the minimum and maximum Brinell hardness of the steel. B. If a hardness test reveals that the Brinell hardness of the steel plate is 260 BHN what is the diameter of the indention in the...

a) A thick steel plate of total area 840 cm2 (both sides) is exposed to air...

a) A thick steel plate of total area 840 cm2 (both sides) is exposed to air near the ocean. After 1 year it was found to have lost 502 g in weight due to corrosion. What is the rate corrosion, or corrosion penetration rate CPR, for the material in this environment? Density of steel = 7.9 g/cm3 [8 marks] b) What type of corrosion is this? [2 marks] c) Provide two strategies (there are more than two of course, but...

If a cylindrical steel pressure vessel has a 400-mm inner radius and 8-mm-thick walls. Find the...

If a cylindrical steel pressure vessel has a 400-mm inner radius and 8-mm-thick walls. Find the change (mm) in the inner radius when the vessel is pressurized to 1.2 MPa. Use E = 200 GPa and v = 0.3 for steel.

A 3/4" diameter hole is to be drilled through 3/4" thick piece of steel plate. The...

A 3/4" diameter hole is to be drilled through 3/4" thick piece of steel plate. The twist drill is to be fed at 0.025 ipr. Maximum cutting speed of 70 fpm is recommended. Calculate: A) Cutting time B) Metal Removal Rate (MRR)

A long metalic strip 1.8 cm wide and 1.0 mm thick is placed in a 1.4-T...

A long metalic strip 1.8 cm wide and 1.0 mm thick is placed in a 1.4-T magnetic field as in the (Figure 1). When a steady current of 17 A passes through it, the Hall emf is measured to be 1.02 μV. Figure1 of 1 Part A Determine the drift velocity of the electrons. Express your answer to two significant figures and include the appropriate units. vd v d = Previous AnswersRequest Answer Incorrect; Try Again; 5 attempts remaining Part...

A base for an airport runway, 100 m wide, 2000 m long and 500 mm thick,...

A base for an airport runway, 100 m wide, 2000 m long and 500 mm thick, is to be constructed out of a clayey sand excavated from a nearby borrow pit, where the in situ water content is 6%. This soil is being transported in trucks having a capacity of 8 m 3 , where each load weighs 13200 kg. In the subbase course, the soil will be placed at a water content of 14.2% to a dry density of...

A plain carbon steel ball 2 mm in diameter is heated to 1200 K in an...

A plain carbon steel ball 2 mm in diameter is heated to 1200 K in an oven and then cooled slowly in ambient air at 300 K. The convection heat transfer coefficient between air and this steel ball is 20 W / (m2 * K). You can find the density, specific heat and thermal conductivity from the property tables attached in text book with reasonable assumptions. Please derive an equation estimating the changes of the temperature of this ball with...

Question