A pond 2 m in diameter is to be filled with water by a flow that...

A pond 2 m in diameter is to be filled with water by a flow that varies linearly with the level of the pond so that it reaches the maximum value of 217 lt/h when the pond is empty and is zero when the level reaches 2 m. Calculate: a) Time it takes to reach the level of 1 m. b) Time it takes to fill up completely. Discuss this last result.

Expert Solution

Amanda K answered 1 year ago

A conical tank of diameter 6 m and height 10 m is filled with water. Compute...

A conical tank of diameter 6 m and height 10 m is filled with water. Compute for the work needed to pump all the water 2 m above the tank. The water has a density of 1000 kg per cubic meter.

A 5.00-m-diameter garden pond is 0.500 m deep. Solar energy is incident on the pond at...

A 5.00-m-diameter garden pond is 0.500 m deep. Solar energy is incident on the pond at an average rate of 400 W/m2. If the water absorbs all the solar energy and does not exchange energy with its surroundings, how many hours will it take to warm from 16.0 ∘C to 19.0 ∘C?

A packed bed reactor is 2 m long with 0.2 m diameter. The reactor is filled...

A packed bed reactor is 2 m long with 0.2 m diameter. The reactor is filled with 1000 spherical particles with a diameter of 5 mm. Air enters the reactor at a volumetric flow rate of 0.0X m3/s. At these conditions, density of air is 1.2 kg/m3 with a viscosity y of 3.0 x 10-5 Pa.s. Calculate: - Porosity of the bed reactor. - The gas mass velocity, G. - Re number, at this value of Re would kinetics or...

A cylindrical can 0.90m high with a diameter of 0.30m is filled with water to a...

A cylindrical can 0.90m high with a diameter of 0.30m is filled with water to a depth of 0.70m from the bottom. A small hole with a cross sectional area of 0.004m^2 is in the side of the can at the bottom. Density of water is 1000kg/m^3 What is the speed of water flowing out of the bottom of the can?

cylindrical container with circular hole at the bottom with diameter d , is filled with water...

cylindrical container with circular hole at the bottom with diameter d , is filled with water to height h . Which of the following statement is correct for the itime required to empty the container If d is constant , the time is inversely proportional to the height of water . If h is constant , the time is inversely proportional to the area of hole . If his constant , the time is directly proportional to the area of...

The 1.3-m-diameter tank is initially filled with gasoline. There is a 3.2-cm-diameter orifice in the bottom....

The 1.3-m-diameter tank is initially filled with gasoline. There is a 3.2-cm-diameter orifice in the bottom. If the orifice is suddenly opened, estimate the time (minutes) for the fluid level to drop from 2m to 1.2 m. Use SG (gas) = 0.66, Cd = 0.63

A hot liquid is filled in a spherical tank with an inner diameter of 3 m...

A hot liquid is filled in a spherical tank with an inner diameter of 3 m and a wall thickness of 3 cm. The tank wall is made of a material with a thermal conductivity of 0.15 W/m∙K. The hot liquid in the tank causes the inner surface temperature to be 100°C, while the tank outer surface is exposed to air at 20°C and has an emissivity of 0.35. Determine the outer surface temperature of the tank. Assume that the...

A swimming pool, 10.0 m by 4.0 m, is filled with water to a depth of...

A swimming pool, 10.0 m by 4.0 m, is filled with water to a depth of 3.0 m at a temperature of 20.2°C. If the energy needed to raise the temperature of the water to 26.1°C is obtained from the combustion of methane (CH4), what volume of methane, measured at STP, must be burned? ∆Hcombustion for CH4 = -891 kJ/mol volume CH4 needed

Spherical particle of silica of 0.1mm diameter falls in water filled in a glass cylinder of...

Spherical particle of silica of 0.1mm diameter falls in water filled in a glass cylinder of 40 mm internal diameter. Estimate the terminal settling velocity of single particle of silica. Also calculate the terminal settling velocity of silica particles when mass ratio of water to silica is 5. .

An axial flow fan has a hub diameter of 1.50 m and a tip diameter of...

An axial flow fan has a hub diameter of 1.50 m and a tip diameter of 2.0 m. It rotates at 18 rad/s and when handling 5.0?^(3)s^(-1) of air, develops a theoretical head equivalent to 17mm of water. Determine the blade outlet and inlet angles at the hub and the tip. Assume that the velocity of flow is independent of radius and that the energy transfer per unit length of blade is constant. Assume density of air is1.2 kg/m^3

Question