Question
In: Mechanical Engineering
Ideal Reheat Steam Cycle (10) Consider a steam power plant operating on the ideal reheat Rankine...
Ideal Reheat Steam Cycle (10)
Consider a steam power plant operating on the ideal reheat Rankine cycle. Steam enters the high-pressure turbine at PH MPa and TH °C and is condensed in the condenser at a pressure of PL kPa. Assume the steam is reheated to the inlet temperature of the high-pressure turbine, and that pump work is NOT negligible. If the moisture content of the steam at the exit of the low-pressure turbine is not to exceed w% percent, determine:
(a) the pressure at which the steam should be reheated and show how you got the quality,
(b) the total turbine work ,
(c) the net work ,
(d) the total heat input , and
(e) the thermal efficiency of the cycle .
PH = 20 MPa, TH = 700 °C, PL = 10 kPa and w% = 12.9%.
Solutions
samet mamat answered 5 months agoRelated Solutions
Consider a steam power plant operating on the ideal reheat Rankine cycle. Steam enters the high-pressure...
Consider a steam power plant operating on the ideal reheat
Rankine cycle. Steam enters the high-pressure turbine at
PH MPa and
TH °C and is condensed in the
condenser at a pressure of PL
kPa. Assume the steam is reheated to the inlet
temperature of the high-pressure turbine, and that pump work is NOT
negligible. If the moisture content of the steam at the exit of the
low-pressure turbine is not to exceed
w% percent, determine:
(a) the pressure at...
Consider a steam power plant operating on a simple ideal Rankine cycle in which the steam...
Consider a steam power plant operating on a simple ideal Rankine
cycle in which the steam enters the turbine at 3 MPa and 350C and
is condensed in the condenser at 75 kPa. Determine the thermal
efficiency of this cycle and sketch an appropriately labeled T-s
diagram. Also compare this thermal efficiency to that a Carnot heat
engine operating between these same two limits.
The change in enthalpy across the pump = work done by the pump:
h2-h1= v1(P2– P1)
A proposed steam power plant design consists of an ideal Rankine cycle with reheat and regeneration....
A proposed steam power plant design consists of an ideal Rankine
cycle with reheat and regeneration. Steam enters Turbine 1 at P1
and T1 at the rate of m1 and exits at P2. A fraction (y') of the
steam exiting Turbine 1 is diverted to an open feedwater heater
while the remainder is reheated to T3 before entering Turbine 2.
The condenser operates at P4. Saturated liquid exits the condenser
and is fed to Pump 1. The outlet of Pump...
Consider a steam power plant operating on the simple ideal Rankine cycle. Steam enters the turbine...
Consider a steam power plant operating on the simple ideal
Rankine cycle. Steam enters the turbine at 15 MPa and 600°C. The
steam condenses in the condenser at 10 kPa. Use the EES software to
study the effects of the following cases on the cycle performance
and to sketch the T-s diagram for each case:
Plot the variation of the cycle thermal efficiency with the
turbine isentropic efficiency. Take the isentropic efficiency of
the turbine in the range 70% to...
Consider a steam power plant operating on the simple ideal Rankine cycle. Steam enters the turbine...
Consider a steam power plant operating on the simple ideal
Rankine cycle. Steam enters the turbine at 15 MPa and 600°C. The
steam condenses in the condenser at 10 kPa. Use the EES software to
study the effects of the following cases on the cycle performance
and to sketch the T-s diagram for each case:
#Plot the variation of the cycle thermal efficiency with the
turbine isentropic efficiency. Take the isentropic efficiency of
the turbine in the range 70% to...
Consider a steam power plant that operates on a reheat Rankine cycle and has a net...
Consider a steam power plant that operates on a reheat Rankine
cycle and has a net power output of 80 MW. Steam enters the
high-pressure turbine at 10 MPa and 500°C and the low-pressure
turbine at 1 MPa and 500°C. Steam leaves the condenser as a
saturated liquid at a pressure of 10 kPa. The isentropic efficiency
of the turbine is 78 percent and that of the pump is 95
percent.
a.)Determine the quality (or temperature, if superheated) of the...
Consider a steam power plant that operates on a reheat Rankine cycle and has a net...
Consider a steam power plant that operates on a reheat Rankine
cycle and has a net power output of 80 MW.
Steam enters the high-pressure turbine at 10 MPa and 500°C and the
low-pressure turbine at 1 MPa and 500°C. Steam leaves the condenser
as a saturated liquid at a pressure of 10 kPa. The isentropic
efficiency of the turbine is 80 percent, and that of the pump is 95
percent. Show the cycle on a T-s diagram with respect...
Consider a steam power plant that operates on a reheat Rankine cycle and has a net...
Consider a steam power plant that operates on a reheat Rankine
cycle and has a net power output of 80 MW. Steam enters the
high-pressure turbine at 10 MPa and 500°C and the low-pressure
turbine at 1 MPa and 500°C. Steam leaves the condenser as a
saturated liquid at a pressure of 10 kPa. The isentropic efficiency
of the turbine is 76 percent and that of the pump is 95
percent.
A: Determine the quality (or temperature, if superheated) of...
Consider a steam power plant operating on a simple ideal Rankine cycle and having a net...
Consider a steam power plant operating on a simple ideal
Rankine cycle and having a net power output of 57 MW. The steam
enters the turbine at 9 MPa and 575 ° C and exits at 150 ° C, then
it is cooled in the condenser to a pressure of 100 kPa by means of
the cooling water from a lake and that circulates through the
condenser tubes to a rate of 1370 kg / s. Consider leaving the pump...
The net power of a steam power plant operating according to the simple ideal Rankine cycle...
The net power of a steam power plant operating according to the
simple ideal Rankine cycle is 30.5 MW. Water vapor enters the
turbine at 7 MPa pressure and 500 ° C, expands to 10 kPa condenser
pressure in the turbine. The steam is condensed in the condenser by
cooling it with water from a lake. The flow rate of the lake water
is 1950 kg / h. Get the pump and turbine adiabatic efficiency of
87%. Show the cycle...
ADVERTISEMENT
ADVERTISEMENT
Latest Questions
- Suppose Rialto is the only movie cinema in a small college town, so it is essentially...
- With VMI, members of the supply chain share planning, demand, forecasting, and inventory information.
- Large lots are desirable in supply chain coordination despite increasing holding costs.
- ***Convert the C++ to Python*** #include <iostream> using std::cout; using std::cin; using std::endl; int charClass; char...
- Make-or-Buy Decision Fremont Computer Company has been purchasing carrying cases for its portable computers at a...
- The following costs were incurred for the single product produced during the first year of operations...
- Non-constant growth model: Do=$2.00 required return on equity= 5% g= 9% n=1,2 g=7% n=3,4 g=3% n=5...
ADVERTISEMENT