Question

In: Other

2.5m long, 10 mm internal diameter tubes required in a shell and tube heat exchanger to...

2.5m long, 10 mm internal diameter tubes required in a shell and tube heat exchanger to increase the temperature of the 3.46kg/s of a process liquid from 20 degree celcius to 80 degree celcius. Condensing steam at 120 degree celcius is the heat transfer medium. Assume that the mean density and specific heat capacity of the process liquid are 1180kg/meter cube and 2350J/kgK, and that the mean overall heat transfer coefficient based on the inside area of the tubes is 950 W/squere meter K, calculate number of tubes_______________

Solutions

Expert Solution

Amanda K answered 5 months ago
Next > < Previous

Related Solutions

A shell-and-tube heat exchanger uses cooling water in the tubes. There are two pressure gages installed...
A shell-and-tube heat exchanger uses cooling water in the tubes. There are two pressure gages installed on the the water side to the heat exchanger. Gage 1 (P1) is installed on the inlet water line, which is connected to the lower nozzle, while Gage (P2) is installed on the discharge water line, which is connected to the upper nozzle. Both pressure gages are very near the nozzle flanges. The pressure drop from each pressure gage to the exchanger channel is...
The purchased cost of a shell-and-tube heat exchanger (floating-head and carbon-steel tubes) with 100 m2 of...
The purchased cost of a shell-and-tube heat exchanger (floating-head and carbon-steel tubes) with 100 m2 of heating surface was $4500 in 1990. What will be the 1990 purchased cost of a similar heat exchanger with 20 m2 of heating surface if the purchased cost capacity expo- nent is 0.60 for surface areas ranging from 10 to 40 m2? If the purchased cost capacity expo- nent for this type of exchanger is 0.81 for surface areas ranging from 40 to 200...
liquid oil is used in the tube side of a shell-and-tube heat exchanger with two shell...
liquid oil is used in the tube side of a shell-and-tube heat exchanger with two shell passes and four tube passes. water is heated in the shell side from 10°C to 50°C while the oil is cooled from 90°C to 60°C. the overall heat transfer coefficient is 53 W/m^2*K. the specific heat of the oil is 2.0 kJ/kg*K. Using the NTU - effectiveness method, calculate the area of the heat exchanger for a total energy transfer of 500 kW. what...
A shell and tube type of heat exchanger with one shell pass and two tube passes...
A shell and tube type of heat exchanger with one shell pass and two tube passes will be designed to provide the given heat transfer rate Q(kW) to cool hot water by using cold river water . The hot water flows through the shell and the cold water flows through the tubes. The inlet and outlet temperatures of the hot water and the cold water are given as Thi, The and Tci, Tce in degrees Celcius. Design the shell and...
A shell and tube type of heat exchanger with one shell pass and two tube passes...
A shell and tube type of heat exchanger with one shell pass and two tube passes will be designed to provide the given heat transfer rate Q(kW) to cool hot water by using cold river water . The hot water flows through the shell and the cold water flows through the tubes. The inlet and outlet temperatures of the hot water and the cold water are given as Thi, The and Tci, Tce in degrees Celcius. Design the shell and...
A shell-and-tube heat exchanger is to used to heat water (in the tube side) from 30...
A shell-and-tube heat exchanger is to used to heat water (in the tube side) from 30 deg C to 40 deg C at a mass flow rate of 4 kg/s. The fluid used for heating (shell side) is water entering at 90 deg C with a mass flow rate of 2 kg/s. A 1-2 STHE is used and the overall heat transfer coefficient based on the inside area is 1390 W/m2-K. The tubes are 1.875 in diameter (inside) and require...
A shell and tube heat exchanger is to be desined by kern's method to heat Toluene....
A shell and tube heat exchanger is to be desined by kern's method to heat Toluene. Toulene: T(in)=100F, T(out)=257F, flowrate=125000Ib/hr P(in)=90Psia composition:100% Toluene. Styrene: T(in)=300F, T(out)=176F, P(in)=50psia composition:100% Styrene What is the mass flow rate of Styrene? Which fluid should be in the shell side and which should be in the tube side and why?
A shell-and-tube heat exchanger with two tube passes and baffled single shell pass is used as...
A shell-and-tube heat exchanger with two tube passes and baffled single shell pass is used as oil cooler. Cooling water at 20°C flows through the tubes at a flow rate of 4.082 kg/s. Engine oil enters the shell side at a flow rate of 10 kg/s. The inlet and outlet temperatures of oil are 90°C and 60°C, respectively. The overall heat transfer coefficient based on the outside tube area (Uo) is 262 W/m2⋅K. The specific heats of water and oil...
The condenser of a thermoelectric plant is a shell and tube heat exchanger consisting of a...
The condenser of a thermoelectric plant is a shell and tube heat exchanger consisting of a shell and 30,000 tubes, each of which executes two steps. The tubes are thin- walled with D = 25 mm, and the steam condenses on its outer surface with a convection coefficient of ho = 11 kW/m2 K. The heat transfer that the exchanger must perform is 2,000 MW, and this is carried out by passing cooling water through the pipes at the rate...
An oil cooler is in the form of a single shell 4 tube heat exchanger in...
An oil cooler is in the form of a single shell 4 tube heat exchanger in which oil passes through the tubes and cool water passes through the shell. Water comes in at 15C and leaves at 25C and has a mass flow rate of 20 kg/min. Oil enters at 35C with a mass flow rate of 30 kg/min. Cp of oil is 2.13 kJ/KgC and that of water is 4.18 kJ/kgC. If the surface area of the heat exchanger...
ADVERTISEMENT
Subjects
ADVERTISEMENT
Latest Questions
ADVERTISEMENT