Question

In: Mechanical Engineering

An oil cooler is in the form of a single shell 4 tube heat exchanger in...

An oil cooler is in the form of a single shell 4 tube heat exchanger in which oil passes through the tubes and cool water passes through the shell. Water comes in at 15C and leaves at 25C and has a mass flow rate of 20 kg/min. Oil enters at 35C with a mass flow rate of 30 kg/min. Cp of oil is 2.13 kJ/KgC and that of water is 4.18 kJ/kgC. If the surface area of the heat exchanger is 0.5 m2, calculate the overall heat transfer coefficient. Assume the heat exchanger is adiabatic with regards to the surroundings.

Solutions

Expert Solution


Related Solutions

liquid oil is used in the tube side of a shell-and-tube heat exchanger with two shell...
liquid oil is used in the tube side of a shell-and-tube heat exchanger with two shell passes and four tube passes. water is heated in the shell side from 10°C to 50°C while the oil is cooled from 90°C to 60°C. the overall heat transfer coefficient is 53 W/m^2*K. the specific heat of the oil is 2.0 kJ/kg*K. Using the NTU - effectiveness method, calculate the area of the heat exchanger for a total energy transfer of 500 kW. what...
A shell-and-tube heat exchanger with two tube passes and baffled single shell pass is used as...
A shell-and-tube heat exchanger with two tube passes and baffled single shell pass is used as oil cooler. Cooling water at 20°C flows through the tubes at a flow rate of 4.082 kg/s. Engine oil enters the shell side at a flow rate of 10 kg/s. The inlet and outlet temperatures of oil are 90°C and 60°C, respectively. The overall heat transfer coefficient based on the outside tube area (Uo) is 262 W/m2⋅K. The specific heats of water and oil...
Design of Shell and Tube Heat Exchanger Crude oil at 198°C is to be cooled to...
Design of Shell and Tube Heat Exchanger Crude oil at 198°C is to be cooled to 39°C. The oil flow-rate is 6.127 kg/s. Cooling water is available at 29°C and at the rate of 27.127 kg/s. The pressure drop allowance for each stream is 100 kN/m2 . Design a suitable shell and tube heat exchanger for this duty. The following are the properties of the two streams at the average temperature: water crude oil density kg/m3 990 850 viscosity mNm-2...
In the two-tube heat exchanger with the same axis used as engine oil cooler, cold water...
In the two-tube heat exchanger with the same axis used as engine oil cooler, cold water enters the steel pipe with inner/outer diameter of 25/30 mm (K= 55 W/mK) entering with at 15°C temperature, 0.5 m/s speed and comes out at 25°C temperature. Hot oil enters the steel pipe with inner/outer diameter of 40/46 mm with a speed of 0.25 m/s at 60°C temperature. According to the oil is required to be cooled at 5°C; A) Find the pipe length...
A shell and tube type of heat exchanger with one shell pass and two tube passes...
A shell and tube type of heat exchanger with one shell pass and two tube passes will be designed to provide the given heat transfer rate Q(kW) to cool hot water by using cold river water . The hot water flows through the shell and the cold water flows through the tubes. The inlet and outlet temperatures of the hot water and the cold water are given as Thi, The and Tci, Tce in degrees Celcius. Design the shell and...
A shell and tube type of heat exchanger with one shell pass and two tube passes...
A shell and tube type of heat exchanger with one shell pass and two tube passes will be designed to provide the given heat transfer rate Q(kW) to cool hot water by using cold river water . The hot water flows through the shell and the cold water flows through the tubes. The inlet and outlet temperatures of the hot water and the cold water are given as Thi, The and Tci, Tce in degrees Celcius. Design the shell and...
A shell-and-tube heat exchanger is to used to heat water (in the tube side) from 30...
A shell-and-tube heat exchanger is to used to heat water (in the tube side) from 30 deg C to 40 deg C at a mass flow rate of 4 kg/s. The fluid used for heating (shell side) is water entering at 90 deg C with a mass flow rate of 2 kg/s. A 1-2 STHE is used and the overall heat transfer coefficient based on the inside area is 1390 W/m2-K. The tubes are 1.875 in diameter (inside) and require...
A shell and tube heat exchanger is to be desined by kern's method to heat Toluene....
A shell and tube heat exchanger is to be desined by kern's method to heat Toluene. Toulene: T(in)=100F, T(out)=257F, flowrate=125000Ib/hr P(in)=90Psia composition:100% Toluene. Styrene: T(in)=300F, T(out)=176F, P(in)=50psia composition:100% Styrene What is the mass flow rate of Styrene? Which fluid should be in the shell side and which should be in the tube side and why?
Write an introduction about heat exchangers and heat exchanger type (single shell pass, four tube pass...
Write an introduction about heat exchangers and heat exchanger type (single shell pass, four tube pass shell and tube heat exchanger). Provide necessary references and citations (Harvard system).
The condenser of a thermoelectric plant is a shell and tube heat exchanger consisting of a...
The condenser of a thermoelectric plant is a shell and tube heat exchanger consisting of a shell and 30,000 tubes, each of which executes two steps. The tubes are thin- walled with D = 25 mm, and the steam condenses on its outer surface with a convection coefficient of ho = 11 kW/m2 K. The heat transfer that the exchanger must perform is 2,000 MW, and this is carried out by passing cooling water through the pipes at the rate...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT