Through a double tube exchanger hot water circulates through the inner tube and water fry through...

Through a double tube exchanger hot water circulates through the inner tube and water
fry through the outer tube. For countercurrent arrangement the following data is displayed:
Cold water inlet temperature Tca 24.5 ° C
Cold water outlet temperature Tcb 48.0 ° C
Hot water inlet temperature Tha 86 ° C
Hot water outlet temperature Thb 55 ° C
Cold water flow 2.00 gal / min
Calliente water flow 2.00 gal / min
Transfer area 0.65 m2 Length of the two pipes is the same 186 cm
to. Build the temperature vs. length diagram
b. Calculate the ΔT1 and ΔT2 approaches c. The temperature ranges ΔTc and ΔTh
d. The average log temperature
and. The global coefficient of heat transfer

Expert Solution

We mostly use countercurrent heat exchanger beacuse in which we get more log mean temperature difference than cocurent or parallel by which we required less surface area for Given heat transfer. Cost of heat exchanger depends upon its surface area which decides how many tubes are required for given heat load.

Amanda K answered 7 months ago

A shell-and-tube heat exchanger is to used to heat water (in the tube side) from 30...

A shell-and-tube heat exchanger is to used to heat water (in the tube side) from 30 deg C to 40 deg C at a mass flow rate of 4 kg/s. The fluid used for heating (shell side) is water entering at 90 deg C with a mass flow rate of 2 kg/s. A 1-2 STHE is used and the overall heat transfer coefficient based on the inside area is 1390 W/m2-K. The tubes are 1.875 in diameter (inside) and require...

A shell-and-tube heat exchanger heats oil from 2°C to 35°C using hot water. The oil flows...

A shell-and-tube heat exchanger heats oil from 2°C to 35°C using hot water. The oil flows in the shell in a single pass. Water flows in 5 copper tubes with a total (all tubes) rate of 0.5 kg/s. Each tube makes 4 passes through the shell and the length per pass is 4 m. The tube inner and outer diameters are 15 mm and 19 mm. The water enters at 95°C and leaves at 29°C. 1. Estimate the average convection...

Heat transfer In a test in a double tube heat exchanger the following data are obtained...

Heat transfer In a test in a double tube heat exchanger the following data are obtained For hot fluid Flow = 11.6 gal / sec Outlet temperature = 30.1 ° C Inlet temperature = 32 ° C For cold fluid Flow 11gal / min Outlet temperature 25.1 ° C Inlet temperature 24.2 ° C For the fluid consider k = 0.49 w / mK cp = 3729.95 J / kgK Prandtl number = 14.29 Density = 1035.02kg / m3 Get:...

Heat transfer in a test in a double tube heat exchanger the following data are obtained...

Heat transfer in a test in a double tube heat exchanger the following data are obtained For hot fluid Flow = 11.6 gal / sec Outlet temperature = 30.1 ° C Inlet temperature = 32 ° C For cold fluid Flow 11gal / min Outlet temperature 25.1 ° C Inlet temperature 24.2 ° C For the fluid consider k = 0.49 w / mK cp = 3729.95 J / kgK Prandtl number = 14.29 Density = 1035.02kg / m3 Get:...

Water flows at 20 cm^3/sec through a long straight tube that has an inner diameter of...

Water flows at 20 cm^3/sec through a long straight tube that has an inner diameter of 1 cm. As the water flows, a toxin leaches from the tube into the water. At the inner surface of the tube, the toxin attains its saturation concentration, Csat = 2 mM. Fortunately, upon entering the water the toxin also irreversibly degrades into a non-toxic compound; this degradation follows first-order kinetics. Toxin Diffusivity D = 10^-5 cm^2/sec Toxin mass transfer coefficient k = 1.38...

heat exchanger has water in the outer conduit and ethylene glycol in the inner. It is...

heat exchanger has water in the outer conduit and ethylene glycol in the inner. It is desired to have a Reynolds number of 1000 in the inner conduit and 15000 in the outer conduit. The inner conduit is 5mm inside diameter and the outer conduit is 12mm inside diameter. Specify the pressure drop per unit length in the each conduit (Pa/m). The inner conduit has a wall thickness of 0.75 mm.

A double pipe heat exchanger is to be designed to cool 5 gal/min of hot oil...

A double pipe heat exchanger is to be designed to cool 5 gal/min of hot oil from 250°F to 120°F using 10 gal/min of cooling water available at 70°F. The heat exchanger is to consist of sections of 0.75 inch 16 BWG copper tubing inside 1.5 inch 16 BWG tubing; the water flows in the annular space. The shell-side heat transfer coefficient for this system is known to be 737 Btu/hr×ft2×°F. a) Estimate the required length of the countercurrent exchanger,...

Hot exhaust gases, which enter a tube heat exchanger with cross-flow fins (both unmixed fluids) at...

Hot exhaust gases, which enter a tube heat exchanger with cross-flow fins (both unmixed fluids) at 1.5 kg/s and 250 oC, are used to heat pressurized water at a speed of 1.0 kg/s and 35 oC. The specific heat of the exhaust gas is 1.0 kJ/kg K, and the overall heat transfer coefficient based on the surface area of the gas side is Uh = 100 22 W/m K and Ah = 40 m . Calculate heat transfer for heat...

A car’s radiator is a heat exchanger with 2 kg/s of hot water entering at 100...

A car’s radiator is a heat exchanger with 2 kg/s of hot water entering at 100 C and leaving at 60 C with a pressure of 200 kPa. Air flows across the heat exchanger entering at 25 C and leaving at 40 C. What is the volume flowrate of air needed in m3/s? (18.9 m3/s)

A shell-and-tube heat exchanger uses cooling water in the tubes. There are two pressure gages installed...

A shell-and-tube heat exchanger uses cooling water in the tubes. There are two pressure gages installed on the the water side to the heat exchanger. Gage 1 (P1) is installed on the inlet water line, which is connected to the lower nozzle, while Gage (P2) is installed on the discharge water line, which is connected to the upper nozzle. Both pressure gages are very near the nozzle flanges. The pressure drop from each pressure gage to the exchanger channel is...

Question