Question

In: Other

Air enters a compressor at 20 oC and atmospheric pressure, and exits at 200 oC and...

Air enters a compressor at 20 oC and atmospheric pressure, and exits at 200 oC and 0.8 MPa. The output stream flows at a linear velocity of 2 m/s, through an exit diameter of 10 cm. What is the power input to the compressor? (Answer: 16.7 kW)

Solutions

Expert Solution


Related Solutions

Fluid (air) enters a nozzle at 150 m/s, 26.85 oC, and at a pressure of 200...
Fluid (air) enters a nozzle at 150 m/s, 26.85 oC, and at a pressure of 200 kPa. Assuming isentropic flow, evaluate the temperature and pressure of the fluid at a location where the speed of fluid equals the speed of sound. What is the ratio of the area at this location to the entrance area?
. In a gas turbine plant, air enters a compressor at atmospheric conditions of 15 ?C,...
. In a gas turbine plant, air enters a compressor at atmospheric conditions of 15 ?C, 1.0133 bar and is compressed through a pressure ratio of 10. The air leaving the compressor passes through a heat exchanger before entering the combustion chamber. The hot gases leave the combustion chamber at 800 ?C and expand through an HP turbine which drives the compressor. On leaving the HP turbine the gases pass through a reheat combustion chamber which raises the temperature of...
Consider a compressor in which air enters at 1 bar, 27°C and exits at 3.5 bar,...
Consider a compressor in which air enters at 1 bar, 27°C and exits at 3.5 bar, 127°C. The work required is 127 kJ/kg of air flowing through the compressor. Heat transfer between the compressor and environment occurs at 27°C. Determine (a) the heat transfer, in kJ/kg (b) the entropy generation rate, in kJ/kg.K, for the compressor as a control volume (c) the entropy generation rate, in kJ/kg.K, for the compressor and the surrounding environment (d) the entropy generation rate, in...
Air enters a compressor operating at steady state with a pressure of 14.7 lbf/in.2, a temperature...
Air enters a compressor operating at steady state with a pressure of 14.7 lbf/in.2, a temperature of 70°F, and a volumetric flow rate of 500 ft3/min. The air velocity in the exit pipe is 700 ft/s and the exit pressure is 133 lbf/in.2 If each unit mass of air passing from inlet to exit undergoes a process described by pv1.34 = constant, determine (a) the exit temperature, in °F, and (b) the diameter of the exit pipe, in inches.
Air enters an adiabatic compressor at 100 kPa (absolute) and 20 ºC at a rate of...
Air enters an adiabatic compressor at 100 kPa (absolute) and 20 ºC at a rate of 0.075 m3 /s, and it exits at a pressure of 900 kPa (absolute). The compressor has an isentropic efficiency of 70 percent. Neglecting the changes in kinetic and potential energies, determine (a) the exit temperature of air and (b) the power required to drive the compressor.
An air compressor is operating at a steady state. The air enters at with a volumetric...
An air compressor is operating at a steady state. The air enters at with a volumetric flow rate 1.2 m^3/s at 170 kPa and 22 degrees celsius with negligible velocity and leaves at 1500 kPa with velocity of 200 m/s. The power to the compressor is 60 kW and the compressor is cooled at a rate of 15 kJ/kg. Determine the exit area.
Air enters a constant diameter pipe at a pressure of 200 kPa. At the exit of...
Air enters a constant diameter pipe at a pressure of 200 kPa. At the exit of the pipe the pressure is 120 kPa, the Mach number is 0.75, and the stagnation temperature is 330°C. Determine the inlet Mach number and the heat transfer per unit mass of air.
Refrigerant 134a enters an air conditioner compressor at 4 bar, 20°C, and is compressed at steady...
Refrigerant 134a enters an air conditioner compressor at 4 bar, 20°C, and is compressed at steady state to 12 bar, 80°C. The volumetric flow rate of the refrigerant entering is 7.5 m3/min. The work input to the compressor is 112.5 kJ per kg of refrigerant flowing. Neglecting kinetic and potential energy effects, determine the magnitude of the heat transfer rate from the compressor, in kW.
In a supermarket, air at atmospheric pressure and 25 °C is supplied to an air handling...
In a supermarket, air at atmospheric pressure and 25 °C is supplied to an air handling unit through a rectangular duct with a cross section of 0.5 m x 0.1 m. The air handling unit will distribute 2/3 of the air to the large shopping area of the supermarket at 25 °C, and it will cool the remaining air to -5 °C and distribute it to a walk-in refrigerator. To avoid frictional pressure losses, the average air velocity in the...
Air enters the compressor of an ideal air standard Brayton cycle at 100 kPa and 290...
Air enters the compressor of an ideal air standard Brayton cycle at 100 kPa and 290 K with a mass flow rate (m⋅) of 6 kg/s. The compressor pressure ratio is 10. The turbine inlet temperature is 1500 K. If a regenerator with an effectiveness of 70% is incorporated in the cycle, determine (a) the thermal efficiency (ηth,Brayton) of the cycle. Use the PG model for air. (b) What-if Scenario: What would the thermal efficiency be if the regenerator effectiveness...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT