Question

In: Other

5.One kilogram of superheated steam at 350°C and 20 bar absolute pressure are sealed in a...

5.One kilogram of superheated steam at 350°C and 20 bar absolute pressure are sealed in a rigid container. Cold water is sprayed on the container until the temperature is 50°C. (Remember that the container is rigid, so the total volume doesn’t change.) a) What is the volume of the container in liters? (Do not assume ideal gas behavior.) Liters b) Is the correct energy balance for this problem based on energy or enthalpy? (answer either enthalpy or internal energy) c) What is the final pressure inside the container (in Pascals)? Pa d) How much of the initial water condenses (g), if any? g e) How much heat was removed from the container while it was being cooled (kJ)? kJ f) How much work was done while the container was being cooled (kJ)? kJ.

Solutions

Expert Solution


Related Solutions

Superheated steam at 20 MPa, 640°C enters the turbine of a vapor power plant. The pressure...
Superheated steam at 20 MPa, 640°C enters the turbine of a vapor power plant. The pressure at the exit of the turbine is 0.5 bar, and liquid leaves the condenser at 0.4 bar at 75°C. The pressure is increased to 20.1 MPa across the pump. The turbine and pump have isentropic efficiencies of 81 and 85%, respectively. Cooling water enters the condenser at 20°C with a mass flow rate of 70.7 kg/s and exits the condenser at 38°C. For the...
One kilogram of Refrigerant 134a vapor initially at 2 bar and 20°C fills a rigid vessel....
One kilogram of Refrigerant 134a vapor initially at 2 bar and 20°C fills a rigid vessel. The vapor is cooled until the temperature becomes -24°C. There is no work during the process. Let To = 20°C, po = 0.1 MPa and ignore the effects of motion and gravity. 2. For the refrigerant, determine the change in exergy, in kJ. Note: for part 1: q=-98.086kj please find part two- the change in exergy in kj
A 5 m3 tank contains superheated steam at 300°C and 22500 mmHg. The tank (and the...
A 5 m3 tank contains superheated steam at 300°C and 22500 mmHg. The tank (and the steam inside) is cooled until the pressure inside is reduced to 2 bar. At this point, liquid water and saturated steam coexist together in the tank. How much heat was removed from the tank, what is the final temperature, and how many kilograms of steam condensed in the process?
An adiabatic steam turbine receives 50 kg/s of superheated steam at 5 MPa and 500oC. Steam...
An adiabatic steam turbine receives 50 kg/s of superheated steam at 5 MPa and 500oC. Steam exits the turbine with a pressure of 100 kPa. Determine the minimum exit quality and the maximum power output of the turbine in kW.
Rankine cycle operates on boiler pressure 15 MPa and condenser pressure of 30 kPa. Superheated steam...
Rankine cycle operates on boiler pressure 15 MPa and condenser pressure of 30 kPa. Superheated steam enters the high-pressure turbine at 450°C. The high-pressure turbine expands the steam and enters the re-heater at 2.5 MPa. The steam is reheated until temperature reaches 450°C before being expanded in low-pressure turbine to condenser pressure of 30 kPa. Assume the isentropic efficiency of the low-pressure and high-pressure turbines are 94% and 89% respectively, and pump is working isentropically. Neglect the change in kinetic...
Superheated steam at 8 MPa and 480°C leaves the steam generator of a vapor power plant....
Superheated steam at 8 MPa and 480°C leaves the steam generator of a vapor power plant. Heat transfer and frictional effects in the line connecting the steam generator and the turbine reduce the pressure and temperature at the turbine inlet to 7.7 MPa and 440°C, respectively. The pressure at the exit of the turbine is 10 kPa, and the turbine operates adiabatically. Liquid leaves the condenser at 8 kPa, 36°C. The pressure is increased to 8.6 MPa across the pump....
Superheated steam at 8 MPa and 480°C leaves the steam generator of a vapor power plant....
Superheated steam at 8 MPa and 480°C leaves the steam generator of a vapor power plant. Heat transfer and frictional effects in the line connecting the steam generator and the turbine reduce the pressure and temperature at the turbine inlet to 7.3 MPa and 440°C, respectively. The pressure at the exit of the turbine is 10 kPa, and the turbine operates adiabatically. Liquid leaves the condenser at 8 kPa, 36°C. The pressure is increased to 8.6 MPa across the pump....
Steam enters an adiabaticnozzle operating at steady state at 20 bar, 320°C, with a velocity of...
Steam enters an adiabaticnozzle operating at steady state at 20 bar, 320°C, with a velocity of 100 m/s. The exit pressure and temperature are 7 bar and 200°C, respectively. The mass flow rate is 5 kg/s. Neglecting potential energychanges, determine: a.the exit velocity, in m/s. b.the exit flow area, in cm2
Problem 2. (50 marks): A superheated steam at 20 bars and 500oC is fed to a...
Problem 2. : A superheated steam at 20 bars and 500oC is fed to a turbine to generate electricity with a capacity of output of work at 500 kJ/kg. The existing steam is a saturated vapor at 2 bars. The surrounding environment temperature is 25oC. The outer surface temperature of the turbine is 150oC 1.) Clearly state your assumptions and draw the process flow diagram with labels ; 2.) Calculate the amount of heat exchanged between the system and surrounding...
A steam turbine receives superheated steam at 18.0 kg/s, 500.°C, and 3.00 MPa and exhausts it...
A steam turbine receives superheated steam at 18.0 kg/s, 500.°C, and 3.00 MPa and exhausts it to 10 kPa with a quality of 96%. If the turbine is assumed to be internally reversible, determine the rate of heat loss from the turbine surface if the power output is 20.MW The surface temperature of the turbine is uniform at 350.°C, and the local environment (ground state) is taken to be saturated liquid water at T0 = 20.0°C. Neglect all flow stream...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT