Question

In: Computer Science

Open the Cisco packet Tracer. Select and add three 3560‐24ps switch to the Cisco packet tracer...

Open the Cisco packet Tracer.

  1. Select and add three 3560‐24ps switch to the Cisco packet tracer window.
  2. Connect each of the switches using cross over cables.
  3. Add three end devices, generic PCs.
  4. Connect each pc to a separate switch using copper strait‐through cables.
  5. When you have completed the steps above; your packet tracer should look like the diagram below and the PCs must be able to ping to each other.

Solutions

Expert Solution

The created network looks like:-

Assigning IP address to each pc:-

click on pc -> click on desktop -> IP configuration -> Enter IP address

Now Ping the two computers:-

click on pc -> click on desktop -> select command prompt -> type command , ping [ip address]


Related Solutions

Using Cisco Packet tracer, drag in three routers and three switches. configure each device with basic...
Using Cisco Packet tracer, drag in three routers and three switches. configure each device with basic items such as wiring them up correct. hostname, banner, password, and turning on the correct interface.
What is a packet switch? What is a circuit switch? What is a message switch? Give...
What is a packet switch? What is a circuit switch? What is a message switch? Give two examples of packet-switched networks and explain how they work.
What is the main differences between Packet Switch Network & Circuit Switch Network?
What is the main differences between Packet Switch Network & Circuit Switch Network?
Use Packet Tracer to complete the following labs. Answer the questions and record screenshots in a...
Use Packet Tracer to complete the following labs. Answer the questions and record screenshots in a Word document labeled firstInitial+LastName+Communications. In this lab, students will explore how ping, traceroute, and the default gateway setting affect device communication. Execute this lab according to the following guidelines: Configure all devices on the network with the following IP addresses: Device IP Address Wrk1 192.168.15.1 Wrk2 192.168.15.2 Sidon1 192.168.15.250 Eden Fa0/0 192.168.15.254 Eden Fa0/1 192.168.16.254 Sidon2 192.168.16.2 Wrk12 192.168.16.1 Open the command prompt for...
Using Packet Tracer Create a Network for 3 departments (sales, accounting, HR) in a business. This...
Using Packet Tracer Create a Network for 3 departments (sales, accounting, HR) in a business. This network should observe reduced collisions and minimum broadcasts. Use private network addressing to simulate the network. PLEASE PROVIDE The network diagram, and pings/simulations to demonstrate the correct functioning of the network. I will rate.
Network Device Basics Directions: Use Packet Tracer to complete the following labs. Answer the questions and...
Network Device Basics Directions: Use Packet Tracer to complete the following labs. Answer the questions and record screenshots in a Word document titled firstInitial+LastName+Basics. Find Device Information You are working with a single active switch and a router as shown in Diagram 1. You would like to gather information about the device. Execute this lab according to the following guidelines: Use the CLI to answer the following questions: What is the IOS version? How much NVRAM (non-volatile RAM) is available...
What does it mean when we say that a Cisco enterprise switch will operate 'out of...
What does it mean when we say that a Cisco enterprise switch will operate 'out of the box'?
Two nodes A and B are connected via switch S. *About packet switching Latency bandwidth :...
Two nodes A and B are connected via switch S. *About packet switching Latency bandwidth : 4Mbps number of packets : 10^3 Propagation time : 2msec size of a packet: 8000 bit (there for there are 8M bit data, 8000 * 10 * 3) switching time : 1msec Queuing time : 0 If a header must be added to the data size (8000 bits), I wonder what is the length condition of the header that will take less time than...
The switch in the figure below is open for t < 0 and is then thrown...
The switch in the figure below is open for t < 0 and is then thrown closed at time t = 0. (a) Find the current in the inductor. (Use the following as necessary: L, R, t, and for .) IL = (b) Find the current in the switch as functions of time thereafter. (Use the following as necessary: L, R, t, and for .) Iswitch =
The switch in the figure below is open for t<0 and is then thrown closed at...
The switch in the figure below is open for t<0 and is then thrown closed at time t = 0. Assume R = 8.00 2, L = 8.00 H, and E = 15.0 V. Find the following as functions of time thereafter. Assume current is in A and time is in s. Use the following as necessary: t.)  (a) the current in the inductor (b) the current in the switch
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT