Question

In: Computer Science

Using Cisco Packet tracer, drag in three routers and three switches. configure each device with basic...

Using Cisco Packet tracer, drag in three routers and three switches.

configure each device with basic items such as wiring them up correct. hostname, banner, password, and turning on the correct interface.

Solutions

Expert Solution

Router(config)#hostname <name of router to change>
Router(config)#enable secret cisco
Router(config)#enable password cisco
Router(config)# banner motd $ "Unauthorised access" $

if you have any doubt then please ask me without any hesitation in the comment section below, if you like my answer then please thumbs up for the answer, before giving thumbs down please discuss the question it may possible that we may understand the question in a different way and I can edit and change the answers if you argue, thanks :)


Related Solutions

Open the Cisco packet Tracer. Select and add three 3560‐24ps switch to the Cisco packet tracer...
Open the Cisco packet Tracer. Select and add three 3560‐24ps switch to the Cisco packet tracer window. Connect each of the switches using cross over cables. Add three end devices, generic PCs. Connect each pc to a separate switch using copper strait‐through cables. When you have completed the steps above; your packet tracer should look like the diagram below and the PCs must be able to ping to each other.
Create a Packet Tracer file that completes the required steps below. Add two Cisco 2960 switches...
Create a Packet Tracer file that completes the required steps below. Add two Cisco 2960 switches and wire it up accordingly; use a crossover cable. Device Interface To Switch 1 G0/0 Switch 2 G0/1 Switch 2 G0/1 Switch 1 G0/0 After you have added the switches, add the following devices and wire accordingly. Device Interface To PC1-A F0 Switch 1 F0/4 PC1-B F0 Switch 1 F0/3 PC2-A F0 Switch 2 F0/4 PC2-B F0 Switch 2 F0/3 Configure the following information...
Design and configure the Star Topology in Packet Tracer with following requirements. • 4 PCs •...
Design and configure the Star Topology in Packet Tracer with following requirements. • 4 PCs • 1 SWITCH • Connection Cable
1- Perform research on the Web and find how Cisco routers and switches can protect against...
1- Perform research on the Web and find how Cisco routers and switches can protect against DDOS. Give a specific example of a Cisco device model. Show the Cisco CLI commands that are used for this purpose 2- The Session Initiation Protocol (SIP) is an important protocol used in Voice over IP phones over the net. Give ONE detailed example of a security attack type of SIP. Explain how we can prevent or mitigate this specific type of attack. Can...
Network Device Basics Directions: Use Packet Tracer to complete the following labs. Answer the questions and...
Network Device Basics Directions: Use Packet Tracer to complete the following labs. Answer the questions and record screenshots in a Word document titled firstInitial+LastName+Basics. Find Device Information You are working with a single active switch and a router as shown in Diagram 1. You would like to gather information about the device. Execute this lab according to the following guidelines: Use the CLI to answer the following questions: What is the IOS version? How much NVRAM (non-volatile RAM) is available...
Using Packet Tracer Create a Network for 3 departments (sales, accounting, HR) in a business. This...
Using Packet Tracer Create a Network for 3 departments (sales, accounting, HR) in a business. This network should observe reduced collisions and minimum broadcasts. Use private network addressing to simulate the network. PLEASE PROVIDE The network diagram, and pings/simulations to demonstrate the correct functioning of the network. I will rate.
course: routing and switching 5. Configure redistribution using valid routing protocols Cisco network Objectives This assessment...
course: routing and switching 5. Configure redistribution using valid routing protocols Cisco network Objectives This assessment task requires you to demonstrate your knowledge of basic Routing Redistribution concepts by completing a number of exercise questions. 5. Configure redistribution using valid routing protocols course Cisco network *
Basic SQL Use the following schema to answer the queries below using SQL DEVICE [dno, dtype,...
Basic SQL Use the following schema to answer the queries below using SQL DEVICE [dno, dtype, price] PROVIDER [pno, pname, web] SERVICE [dno, pno, servicedate] SERVICE.dno references DEVICE.dno SERVICE.pno references PROVIDER.pno bold is underline. a) Find the dno for the most expensive device b) Find all providers that have the work fast in the name c) Find the number of different device types (dtype) d) Give all details of devices with price more than $400
This is done using Visual Basic. Add three text boxes and three buttons to the form....
This is done using Visual Basic. Add three text boxes and three buttons to the form. Set the second and third text boxes' Multiline, ReadOnly, and ScrollBars properties to True, True, and Vertical, respectively. The user will enter a number in the first text box and them click the first button. The first buttons click event procedure should write the number on a seperate line in a sequential access file. The second button's click event procedure should read the entire...
What are the three basic types of solids and the composite units of each? What types...
What are the three basic types of solids and the composite units of each? What types of forces hold each type of solid together?
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT