An old storage tank of “46” m3 stores steam at 6000 kPa and 330 °C. A...

An old storage tank of “46” m3 stores steam at 6000 kPa and 330 °C. A crack develops at the
top wall of the tank and steam starts to leak out to the atmosphere. An engineer realizes the
problem on time and stops the leak when the pressure inside the tank is below 4000 kPa. If
the leak is assumed to be adiabatic and reversible,
a) What is the final temperature of the steam remained in the tank? (10 points)
b) How much steam is released to the atmosphere? (10 points)

Expert Solution

Amanda K answered 6 months ago

An adiabatic tank, 0.5 m3, is initially evacuated and charged with steam at 500 kPa and...

An adiabatic tank, 0.5 m3, is initially evacuated and charged with steam at 500 kPa and 300 C. The final tank pressure is 500 kPa. Determine the final temperature and the entropy production.

A 5 m3 tank contains superheated steam at 300°C and 22500 mmHg. The tank (and the...

A 5 m3 tank contains superheated steam at 300°C and 22500 mmHg. The tank (and the steam inside) is cooled until the pressure inside is reduced to 2 bar. At this point, liquid water and saturated steam coexist together in the tank. How much heat was removed from the tank, what is the final temperature, and how many kilograms of steam condensed in the process?

A 10.0 m3 tank contains steam at 250°C and 10.0 bar. The tank and its contents...

A 10.0 m3 tank contains steam at 250°C and 10.0 bar. The tank and its contents are cooled until the pressure drops to 1.8 bar. Some of the steam condenses in the process. (a) How much heat was transferred from the tank? (b) What is the final temperature of the tank contents? (c) How much steam condensed (kg)?

Thermodynamics A 1 m3 rigid tank has propane at 100 kPa and 300 K. The tank...

Thermodynamics A 1 m3 rigid tank has propane at 100 kPa and 300 K. The tank is connected to another 0.5 m3 rigid tank which has propane at 250 kPa and 400 K by a ball valve. The valve is opened and both tanks come to a uniform state at 325 K. 1- State all assumptions you need to solve the problem. 2- Calculate the final pressure of propane in both tanks? 3- Calculate the mass of propane before and after opening the...

An ideal Rankine cycle with regenerative system. Steam enters the turbine at 6000 kPa and 450oC...

An ideal Rankine cycle with regenerative system. Steam enters the turbine at 6000 kPa and 450oC and is condensed in the condenser at 20 kPa. It the steam is extracted from the turbine at 400 kPa to heat the feedwater in an open feedwater heater and the water leaves the feedwater heater as a saturated liquid. Find the rate of heat added in the boiler? Find the rate of heat rejected in the condenser? Determine the network output per kilogram...

Five kilograms of steam contained in a 2-m3 cylinder at 40 kPa is compressed isentropically to...

Five kilograms of steam contained in a 2-m3 cylinder at 40 kPa is compressed isentropically to 5000 kPa. What is the work needed? Please show correct work. Answer: 185 kJ

A 1.0 m3 tank, initially filled with 103. kPa, 300. K air, is connected to a...

A 1.0 m3 tank, initially filled with 103. kPa, 300. K air, is connected to a source of air at 1,500. kPa, 300. K. The tank slowly fills until it is at the same pressure. If the temperature is maintained at 300. K throughout this transient process, what is the total heat transfer required? (You can assume air is an ideal gas.)

A boiler of a thermoelectric power plant produces 1540.8 m3/h of saturated steam at 900 kPa

A boiler of a thermoelectric power plant produces 1540.8 m3/h of saturated steam at 900 kPa. Determine the mass flow rate of steam produced (kg/s).

An insulated rigid tank having a 0.2 m3 volume initially contains air at 400 kPa and...

An insulated rigid tank having a 0.2 m3 volume initially contains air at 400 kPa and 313 K. The amount of paddle-wheel work done on the system is 200 kJ. Calculate the nearest value of entropy change a. 0.66 kJ/K b. 0.88 kJ/K c. None d. 0.44 kJ/K e. 0.33 kJ/K

For storage options a, b, and c, what volume of storage tank for hydrogen would be...

For storage options a, b, and c, what volume of storage tank for hydrogen would be needed for a hydrogen fuel cell car to have the same delivered transport energy (that is, total vehicle-km of travel) as a conventional car with a full 50 litre petrol tank (note that the actual volume of the tank is more than 50 litre). a- If the hydrogen is stored as compressed gas at a pressure of 350 bar (1 bar = 101 kPa)...

Question