Question

In: Other

The difference in temperature between the boiling refrigerant temperature and the evaporator outlet temperature is known...

The difference in temperature between the boiling refrigerant temperature and the evaporator outlet temperature is known as ___________.

Solutions

Expert Solution

Is known as evaporator superheat.

Refrigerant is the liquid which is used in heat engine or refrigerator cycle which takes the heat from the cycle or give it and changes it phase. Superheat term is used when any component or liquid is above it's saturation temperature. So when refrigerant which is used is in superheated condition then this evaporator superheat which tells about the difference in temperature is used. It tell about the degree at which refrigerant is superheated. There is a level for this parameter which is helpful for technician. If a compound or refrigerant is used whose saturation temperature is 110 degree Celsius and if it is now in 140 degree Celsius the evaporate superheat is 30 degree Celsius. If this temperature is more than permitted level then it means that refrigerant is taking more amount of heat than expected that means the flow of refrigerant is more as heat flow is also dependent on mass flow similarly we can say that if this is less than expected than flow rate of refrigerant is less.


Related Solutions

Assume that the difference in temperature between a condenser and a evaporator decreases. How will the...
Assume that the difference in temperature between a condenser and a evaporator decreases. How will the volumetric efficiency of the cooling compressor be affected by this. Show this by describing it in a pv diagram.
Refrigerant 134a enters the evaporator of a refrigeration system operating at steady state at -4oC and...
Refrigerant 134a enters the evaporator of a refrigeration system operating at steady state at -4oC and a quality of 20% at a velocity of 6 m/s. At the exit, the refrigerant is a saturated vapor at -4oC. The evaporator flow channel has constant diameter of 1.7 cm. Determine the mass flow rate of the refrigerant, in kg/s, and the velocity at the exit, in m/s.
refrigerant 134a enters the evaporator of a refrigeration system operating at steady state at -12°C and...
refrigerant 134a enters the evaporator of a refrigeration system operating at steady state at -12°C and a quality of 20% at a velocity of 7 m/s. At the exit, the refrigerant is a saturated vapor at -12°C. The evaporator flow channel has constant diameter of 1.7cm. Determine the mass flow rate of the refrigerant in kg/s Determine the velocity at the exit in m/s
A simple R134a plant is develop 70000kJ/hr of refrigerant leaves the evaporator as saturated vapor at...
A simple R134a plant is develop 70000kJ/hr of refrigerant leaves the evaporator as saturated vapor at 10 degree c. After isentropic compression the pressure of refrigerant is 10 bar. Draw the P-h diagram and determine 1) the refrigerant flow rate 2) the compressor discharge temperature 3) the heat rejected to the condenser in KW 4) The COP 5) the power required to drive the compressor
100 grams of boiling water (temperature 100
100 grams of boiling water (temperature 100
A triple-effect forward-feed evaporator is used to concentrate a liquid which has marginal elevation in boiling...
A triple-effect forward-feed evaporator is used to concentrate a liquid which has marginal elevation in boiling point. The temperature of the stream to the first effect is 125°C, and the boiling point of the solution within third effect is 45°C. Find out at what temperatures the fluid boils in the Ι and ΙΙ effects. The overall heat transfer coefficients are 2250W/m2 in the Ι-effect, 1800W/m2 in the ΙΙ-effect and 1300W/m2 in the ΙΙΙ-effect respectively.
The particulars of a 20 TR R 22 food freezer are as follows: Evaporator temperature –...
The particulars of a 20 TR R 22 food freezer are as follows: Evaporator temperature – 30°C Condenser temperature 40°C Temperature of vapor leaving evaporator – 25°C Subcooling of liquid with vapor in heat exchanger 5°C Polytropic index of compressor 1.15 Superheating of suction vapor after passing through suction valve 15°C Compressor clearance factor 0.05 Pressure drop in valves 0.2 bar suction 0.5 bar discharge The compressor has 6 cylinders with bore equal to stroke. Its rpm is 1500, and...
The difference between actual revenues and expenses and the flexible budget is known as​ the: A....
The difference between actual revenues and expenses and the flexible budget is known as​ the: A. flexible budget variance B. master budget variance C. static budget variance D. volume variance Identify which responsibility center would best describe the​ following: The production line of American​ Apparel, where clothing is manufactured. A. Revenue Center B. Cost Center C. Profit Center D. Investment Center The subscription sales department of the New York Times. A. Revenue Center B. Cost Center C. Profit Center D....
What is the difference between superalloys and high-temperature stainless steel?
What is the difference between superalloys and high-temperature stainless steel?
In a household refrigerator with evaporator temperature -10 ° C and condenser pressure 1000 kPa R134a...
In a household refrigerator with evaporator temperature -10 ° C and condenser pressure 1000 kPa R134a is used as refrigerant. Saturated steam at the compressor inlet The refrigerant that is in the state is in the state of saturated liquid at the outlet of the condenser. Entropy at the compressor outlet is 0.985 kJ / kgK. According to this, a) Cycle T-s and P-h diagrams, showing saturation curves on the diagram Draw. b) Calculate the isentropic efficiency of the compressor....
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT