Question
In: Physics
A cylinder containing ideal gas is sealed by a piston that is above the gas. The...
A cylinder containing ideal gas is sealed by a piston that is above the gas. The piston is a cylindrical object, with a weight of 36.0 N, which can slide up or down in the cylinder without friction. The inner radius of the cylinder, and the radius of the piston, is 7.00 cm. The top of the piston is exposed to the atmosphere, and the atmospheric pressure is 101.3 kPa. The cylinder has a height of 30.0 cm, and, when the temperature of the gas is 20°C, the bottom of the piston is 14.0 cm above the bottom of the cylinder. (a) Determine the pressure of the gas in the cylinder. kPa (b) Find the number of moles of ideal gas in the cylinder. moles (c) Heat is added, gradually raising the temperature of the gas to 165°C. Calculate the distance between the bottom of the cylinder and the bottom of the piston when the piston comes to its new equilibrium position.
Solutions
If you liked the answer then give a thumb
up.
genius_generous answered 7 months agoRelated Solutions
Constant amount of ideal gas is kept inside a cylinder by a piston. The piston is...
Constant amount of ideal gas is kept inside a cylinder by a
piston. The piston is locked in to position, it is not allowed to
move. The gas is then heated up. Compare the initial (i) and the
final (f) physical quantities of the gas to each other.
(The fill in the blank options are greater than, less than, or
equal too).
The volume Vf is ... Vi.
The temperature Tf is ... Ti.
The internal energy Uf is ......
The drawing shows an ideal gas confined to a cylinder by a massless piston that is...
The drawing shows an ideal gas confined to a cylinder by a
massless piston that is attached to an ideal spring. Outside the
cylinder is a vacuum. The cross-sectional area of the piston is
A = 2.50 × 10-3 m2. The initial
pressure, volume, and temperature of the gas are, respectively,
P0, V0 = 6.00 ×
10-4 m3 and T0 = 273 K,
and the spring is initially stretched by an amount
x0 = 0.090 m with respect to its...
The drawing shows an ideal gas confined to a cylinder by a massless piston that is...
The drawing shows an ideal gas confined to a cylinder by a
massless piston that is attached to an ideal spring. Outside the
cylinder is a vacuum. The cross-sectional area of the piston is A =
2.50 × 10-3 m2. The initial pressure, volume, and temperature of
the gas are, respectively, P0, V0 = 6.00 × 10-4 m3 and T0 = 273 K,
and the spring is initially stretched by an amount x0 = 0.092 m
with respect to its...
1mol of an ideal gas is inside a cylinder with a piston under a pressure of...
1mol of an ideal gas is inside a cylinder with a piston under a
pressure of 6 atm. When reducing the pressure to 2 atm at constant
T = 300K:
(a) Who is doing work, the piston or the gas?
(b) What is the type of process for the maximum work? Find the
maximum amount of work.
(c) What is the type of process for the minimum work? Find the
minimum amount of work.
n ideal gas is enclosed in a cylinder with a movable piston on top of it....
n ideal gas is enclosed in a cylinder with a movable piston on
top of it. The piston has a mass of 8,000 g and an area of 5.00 cm2
and is free to slide up and down, keeping the pressure of the gas
constant. (a) How much work is done on the gas as the temperature
of 0.180 mol of the gas is raised from 30.0°C to 325°C?
A monatomic ideal gas is contanined in a cylinder with a moveable piston. Initially the volume...
A monatomic ideal gas is contanined in a cylinder with a
moveable piston. Initially the volume of the cylinder is 0.25m^3.
The gas is compressed under a constant pressure of 3 Pa until the
volume has been halved. Then the volume is held constant while the
pressure is doubled. Finally, the gas is allowed to expand
isothermally back to its original condition.
a)Sketch a P-V diagram for this process. Label the corners 1, 2,
3 with 1 being the beginning...
An ideal gas is contained in a piston-cylinder device and undergoes a power cycle as follows:...
An ideal gas is contained in a piston-cylinder device and
undergoes a power cycle as follows: 1-2 isentropic compression from
an initial temperature T1 5 208C with a compression ratio r 5 5 2-3
constant pressure heat addition 3-1 constant volume heat rejection
The gas has constant specific heats with cv 5 0.7 kJ/kg·K and R 5
0.3 kJ/kg·K. (a) Sketch the P-v and T-s diagrams for the cycle. (b)
Determine the heat and work interactions for each pro- cess,...
Consider a system consisting of a cylinder with a movable piston containing 106 gas molecules at...
Consider a system consisting of a cylinder with a movable piston
containing 106 gas molecules at 298 K at a volume of 1
L. Consider the following descriptions of this system:
A. Initial system as described
above.
B. Starting from the initial system,
the volume of the container is changed to 2 L and the temperature
to 395 K.
C. Starting from the initial system,
a combination reaction occurs at constant volume and
temperature.
D. Starting from the initial system,...
cooling a gas in a piston cylinder. if the boundary work of piston cylinder is compressed...
cooling a gas in a piston cylinder.
if the boundary work of piston cylinder is compressed
W = -10 kj
determine if it is gained or lost by the gas.
a. If a 6 cm diameter cylinder containing 2 g of an ideal gas at 25o...
a. If a 6 cm diameter cylinder containing 2 g of an ideal gas at
25o C is fitted with a 5 kg piston with a 20 kg weight on the
piston, calculate the pressure and volume of the ideal gas if the
atmospheric pressure is 1 atm. If the 20 kg weight is removed,
provide detailed comments without further calculations on what
would happen. You may assume a molecular weight of 28 for the
gas.
b. Calculate the energy...
ADVERTISEMENT
ADVERTISEMENT
Latest Questions
- 1.Instead of Build-Max-Heap, we could use Heap-Insert-Max to build a tree with heap property. Write a...
- explain why using email address as the primary key for Staff is a bad idea
- You have just received a job offer at an investment bank, an dare offered the 2...
- (C++)Counting Sort: Write C++ codes for counting sort. The input array is A = {20, 18,...
- Describe how to select various cable media and network interface cards (NIC) options for your own...
- In this case,I have been appointed the project manager of a large firm glass making company...
- Explain a specific example in which you utilized problem solving strategies to resolve a real world...
ADVERTISEMENT