If it should happen that a high voltage electric line should drop from the pole and...

If it should happen that a high voltage electric line should drop from the pole and make contact with a car, the person in the car should jump out of the car with both feet at the same time, rather than stepping out, one foot at a time. Explain the rationale behind this safety tip.

Solutions

Expert Solution

genius_generous answered 1 month ago

Next > < Previous

Related Solutions

3. Electric power is transferred at very high voltages over long distances. Transmission of high voltage...

3. Electric power is transferred at very high voltages over long distances. Transmission of high voltage Explain how it reduces power loss on the lines. 4. If two points have the same potential, this test load will be taken from one point to another. Does it mean that no work will be carried out during the course? This need no force application shows that it is not? Discuss.

A high voltage power line carries a current of 105 A at a location where the...

A high voltage power line carries a current of 105 A at a location where the Earth's magnetic field has a magnitude of 0.588 G and points the to the North, 74.7 degrees below the horizontal. Calculate the magnitude of the magnetic force exerted on a 253 m length of wire if the current in the wire flows horizontally toward the east? _____________________________________________________________ Calculate the magnitue of the magnetic force exerted on a 253 m length of wire if the...

Problem 4. A high-voltage power supply should have a nominal output voltage of 350 V. A...

Problem 4. A high-voltage power supply should have a nominal output voltage of 350 V. A sample of four units is selected each day and tested for process-control purposes. The data (see sheet Problem4 in Homework 4.xlsx) give the difference between the observed reading on each unit and the nominal voltage times ten; that is, ?? = (observed voltage on unit ? - 350)*10 (a) Set up ?̅ and ? charts on this process. Is the process in statistical control?...

A high-level voltage power supply should have a nominal output voltage of 350 V. A sample...

A high-level voltage power supply should have a nominal output voltage of 350 V. A sample of four units is selected each day and tested for process-control purposes. The data (20 days, 1 sample/day) shown in the table below give the difference between the observed reading on each unit and the nominal voltage times ten; that is, xi = (observed voltage on unit 350)*10. Voltage Data Voltage Data Sample # xi Sample # xi 1 6 11 8 1 9...

A high-voltage power line carries a current of 122 A at a location where the Earth's...

A high-voltage power line carries a current of 122 A at a location where the Earth's magnetic field has a magnitude of 0.59 G and points to the north, 68 ∘ below the horizontal. Find the direction of the magnetic force exerted on a 330 mm length of wire if the current in the wire flows horizontally toward the east. A:force points toward north, 22 ∘∘ above the horizontal B:force points toward north, 68 ∘∘ above the horizontal C:force points...

From Millikan’s oil drop experiment, what was he value of the voltage that allowed the drops to...

From Millikan’s oil drop experiment, what was he value of the voltage that allowed the drops to obtain terminal velocity?

what is the electric field and electric potential (voltage) at the center and surface of a...

what is the electric field and electric potential (voltage) at the center and surface of a spherical conductor?

Copper and aluminum are being considered for a high-voltage transmission line that must carry a current...

Copper and aluminum are being considered for a high-voltage transmission line that must carry a current of 60 A. The resistance per unit length is to be 0.170 Ω/ km. Compute for each choice of cable material the current density. The current density for copper? The current density for aluminum? Compute the mass per meter of the cable for each material. The densities of the copper and aluminum are 8960 and 2700 kg/ m3, respectively. The mass per meter of...

How is a low voltage two stage electrostatic precipitator different from a high voltage single stage...

How is a low voltage two stage electrostatic precipitator different from a high voltage single stage electrostatic precipitator? Explain the operation of a plate type electrostatic precipitator. Include a schematic view of the electrostatic precipitator and mention the size-efficiency relationship.

Company A is a high voltage equipment manufacturer. They produced high voltage transformers rated 300 kV...

Company A is a high voltage equipment manufacturer. They produced high voltage transformers rated 300 kV and above. All high voltage tests such as AC, DC and impulse have been conducted to the equipment. However, they have been penalized due to non-compliance issue. Justify the root cause of this problem and support with relevant facts.

Subjects