1) Design forms for 13’-8” high wall to be concreted at the rate of 5 ft...

1) Design forms for 13’-8” high wall to be concreted at the rate of 5 ft per hour, internally vibrated. Assume the mix is made with Type I cement, with no pozzolans or admixtures, and that the temperature of concrete at placing is 75°F. The unit weight of concrete is 150 pcf with a slump of 3.75 inches. The forms will be used only once, so short-term loading stresses will apply. Use form grade plywood sheathing 7/8 in. thick in 5×10-ft sheets, and 5,250-lb coil ties are on hand. Framing lumber of No. 2 Douglas Fir-Larch is to be purchased as required.

Design for SHEATHING and STUD SIZE.

Expert Solution

Ally Wells answered 9 months ago

A body of water is being retained by a concrete dam wall (15 ft high and...

A body of water is being retained by a concrete dam wall (15 ft high and 6 ft thick). What is the maximum height the water can rise without causing the intensity of pressure at the toe greater than twice the average pressure on the base? Assume that concrete weighs 150 lbs per cubic foot, there is no seepage causing uplift against the bottom of the wall, and water weighs 62.5 lbs per cubic foot.

Design a 9 ft cantilever if a dead load 1 k / ft ( not including...

Design a 9 ft cantilever if a dead load 1 k / ft ( not including the beam weight ) and live load of 1 k / ft . use fc ' = 3800 psi and fy = 60,000 psi . ( Hint : Rectangular section , answer should be in In " 2 for Area of steel and in inches for width and height )

A 17-ft-high retaining wall is restrained from yielding. The shear strenght parameters are c = 0...

A 17-ft-high retaining wall is restrained from yielding. The shear strenght parameters are c = 0 and φ33 The water table being 7 ft below the surface. The saturated unit weights of the rock is 122 lb/ft³, above the water table the (dry) unit weight of the rock is 104 lb/ft³. Assume that for OCR= 2. Calculate the lateral force Po per unit length of the wall. Also, determine the location of the resultant force.

Determine the maximum allowable span of nominal 2x4 wall forms studs carrying a design load...

Determine the maximum allowable span of nominal 2x4 wall forms studs carrying a design load of 1000 psf. Stud spacing is 16” on center. Use the allowable stresses for Douglas Fir from Table 13-8 and 7 day load duration. Assume that studs are continuous over 3 or more spans. Limit deflection to l/360 of span length. Based on the maximum allowable span, check for crushing of studs on double 2x4 wales. Conditions are dry.

1. A house is 42.0 ft long and 38.0 ft wide and has 8.0-ft-high ceilings. What...

1. A house is 42.0 ft long and 38.0 ft wide and has 8.0-ft-high ceilings. What is the volume of the interior of the house in cubic meters and cubic centimeters? _________ m^3 _________ cm^3 2. An auditorium measures 45.0 m ✕ 30.0 m ✕ 7.0 m. The density of air is 1.20 kg/m3. (a) What is the volume of the room in cubic feet? _________ ft^3 (b) What is the weight of air in the room in pounds? _________...

A converging lens forms an image 20 centimeters high of an object that is 5 centimeters high....

A converging lens forms an image 20 centimeters high of an object that is 5 centimeters high. part a calculate the magnification factor m of the lens part b Explain how you can calculate the distance from the object if you know the lens has a focal length of f centimeters. part c If the lens has a focal length of 10 centimeters calculate the distance to the image if the object is placed at a distance of 25 centimeters from the...

The Fibonacci series 0, 1, 1, 2, 3, 5, 8, 13, 21 … begins with the...

The Fibonacci series 0, 1, 1, 2, 3, 5, 8, 13, 21 … begins with the terms 0 and 1 and has the property that each succeeding term is the sum of the two preceding terms. Write a non-recursive function Fibonacci (n) that calculates the nth Fibonacci number. Write a program to display a table of terms and the Fibonacci number in two columns for the first 15 terms, using the function you created.

The Fibonacci sequence is the series of integers 0, 1, 1, 2, 3, 5, 8, 13,...

The Fibonacci sequence is the series of integers 0, 1, 1, 2, 3, 5, 8, 13, 21, 34, 55, 89 . . . See the pattern? Each element in the series is the sum of the preceding two elements. Here is a recursive formula for calculating the nth number of the sequence: Fib(N) = {N, if N = 0 or 1 Fib(N - 2) + Fib(N - 1), if N > 1 a) Write a recursive method fibonacci that returns...

Given a wall that is 36 feet long and 8 feet high calculate the heat loss...

Given a wall that is 36 feet long and 8 feet high calculate the heat loss per hour when the inside temperature is 70 degrees inside and 10 degrees outside. The wall assembly consists of: A = Face brick B = 1” Polystyrene ins. board C = 2 X 6 studs D = Fiberglass batt ins. E = ½” Sheet rock F = Paneling

Design an active high pass filter with a high frequency gain of 5 and a cutoff...

Design an active high pass filter with a high frequency gain of 5 and a cutoff frequency of 2kHz. Use a 0.1 uF capacitor in your design.

Question