Question
In: Civil Engineering
Design a 9 ft cantilever if a dead load 1 k / ft ( not including...
Design a 9 ft cantilever if a dead load 1 k / ft ( not including the beam weight ) and live load of 1 k / ft . use fc ' = 3800 psi and fy = 60,000 psi . ( Hint : Rectangular section , answer should be in In " 2 for Area of steel and in inches for width and height )
Solutions
Expert Solution
width 12inch
depth 16.2 inch
area of steel= 2.37 in2
sir, hope this helped u
sir, please please give an up-rating
Ally Wells answered 1 year agoRelated Solutions
Select a 12 ft cantilever beam with p = 0.012, to support a dead load of...
Select a 12 ft cantilever beam with p = 0.012, to
support a dead load of 2k/f (including self weight) and Live load
of 3 k/ft. fy= 60000 psi, fc'= 3500 psi (hint your answer should be
Width = XXXX, Effective depth= XXXXX, Area of reinforcement =
XXXXX)
Design for flexure a beam 12 ft in length, having a uniformly distributed dead load of...
Design for flexure a beam 12 ft in length, having a uniformly
distributed dead load of 1 kip/ft, a uniformly distributed live
load of 1 kip/ft, and a concentrated dead load of 8.4 kips a
distance of 5 ft from one support Show all the steps. (LRFD) Fy =
50k/in2 E = 29,000k/in2
A Simply supported rectangular, tension-reinforced beam is to be designed for dead load of 0.75 k/ft...
A Simply supported rectangular, tension-reinforced beam is to be
designed for dead load of 0.75 k/ft plus self weight and service
live load of 2.0 k/ft, with a 30 -ft simple span. Material strength
will be fy = 60 ksi and fc = 5 ksi for steel and normal weight
concrete respectively.
Start the design of the beam dimensions using the rules of
thumbs in class. The total beam depth, h, must not exceed twice the
width.
Calculate the required...
A Simply supported rectangular, tension-reinforced beam is to be designed for dead load of 0.75 k/ft...
A Simply supported rectangular, tension-reinforced beam is to be
designed for dead load of 0.75 k/ft plus self weight and service
live load of 2.0 k/ft, with a 30 -ft simple span. Material strength
will be fy = 60 ksi and fc = 5 ksi for steel and
normal weight oncrete respectively.
Startthe design of the beam dimensions using the rules of thumbs
in class. The total beam depth, h, must not exceed twice
the width.
Calculate the required beam...
1) Design a Tied column to support axial Dead load D = 280 K and axial...
1) Design a Tied column to support axial Dead load D = 280 K and
axial live load = 500 k, initially assume 2% longitudinal
reinforcement f’c = 4000 psi, fy = 60,000 psi.
2) Sketch the column cross-section and show long bars and
ties
Design a square tied column to support an axial dead load of (W1) k and an...
Design a square tied column to support an axial dead
load of (W1) k and an axial live load of (W2) k.
Begin using approximately (X) percent longitudinal
steel, a concrete strength of 4,000 psi and Grade 60
steel.
Draw the details of reinforcement and
check all ACI recommendation.
W1 = 220 k
W2 = 165 k
X = 2%
A simply supported beam spans 35ft and carries a simply distrusted dead load of 0.2kip/ft including...
A simply supported beam spans 35ft and carries a simply
distrusted dead load of 0.2kip/ft including the beam self-weight
and live load of 0.8kip/ft. Determine the minimum required plastic
section modulus and select the lightest-weight W-shape to carry the
moment. Assume full lateral support and A992 steel. Design by (a)
LRFD and (b) ASD
The service load bending moments on a beam are 128 kip-ft for dead load and 107...
The service load bending moments on a beam are 128 kip-ft for
dead load and 107 kip-ft for live load. The beam is 12 in. wide,
f’c is 3000 psi and fy is 60 ksi. Determine Mu, Mt, p, R, the depth
of the beam and the As of tensile reinforcing required. How many
no. 8 bars or No. 10 bars would have the required As?
A cantilever bean is 12 feet long and has a uniformly distributed dead load of 600...
A cantilever bean is 12 feet long and has a uniformly
distributed dead load of 600 lbs/ft and a uniformly distributed
live load of 1000 lbs/ft. Design the beam for flexure assuming it
is continuously braces by a floor/deck system. Use 36 ksi
steel.
a) draw Free body Diagram/ shear + moment diagram to find Mu
Max
b) Solve for Zx based on Mu Max
c) Select beam from table 9.1
d) Check compactness criteria
e) if compactness works, recalculate...
A 40 ft simple span beam is loaded with a uniform dead load of 2.4 kips/ft...
A 40 ft simple span beam is loaded with a uniform dead load of
2.4 kips/ft plus the beam self-weight and a uniform live load of
3.3 kips/ft. The lateral supports are located at the supports and
at the midpoint of the span. Determine the leastweight W-shape to
carry the load. Use A992 steel and Cb= 1.0. Design by (a) LRFD and
(b) ASD. [6.16-36]
ADVERTISEMENT
ADVERTISEMENT
Latest Questions
- A person walks into a room that has two flat mirrors on opposite walls. The mirrors...
- Sociologists say that 85% of married women claim that their husband's mother is the biggest bone...
- What steps must be taken to build a comprehensive tourism plan?
- The assets of Dallas & Associates consist entirely of current assets and net plant and equipment,...
- Computer System Forensics course a long and comprehensive explanation by typing please 1.What are some notable...
- 10. What are some street names of MDMA? How is MDMA taken? In which categories of...
- Roxie Epoxy’s balance sheet shows a total of $50 million long-term debt with a coupon rate...
ADVERTISEMENT