Question

In: Mechanical Engineering

A vertical axis cylinder 0.075m2 in cross sectional area is open to the atmosphere at one...

A vertical axis cylinder 0.075m2 in cross sectional area is open to the atmosphere at one end and closed at the other by a piston which supports a mass of 85 kg. the piston is supported by compressed air. 5.46kJ of heat is transferred to the air and the piston lifts the mass through 55cm. What is the increase in internal energy, U, during the process? Draw the path of the process on a PV diagram.

Patmos= 1.03 bar Ans=0.75 kJ

Solutions

Expert Solution


Related Solutions

Pure ethanol is contained at the bottom of a long vertical tube( cross sectional area is...
Pure ethanol is contained at the bottom of a long vertical tube( cross sectional area is 0.9 cm2). Above the liquid is a quaescent layer of air.The liquid at the bottom of the tube is carefully adpuruted so that the distance from the air liquid interface to the open top of the tube is constant at 15 cm . No liquid is withdrawn from the tube. At the open end of the tube is perpendicular to the vertical tube so...
The figure below shows a closed cylinder with cross-sectional area A = 2.60 m2. The upper...
The figure below shows a closed cylinder with cross-sectional area A = 2.60 m2. The upper and lower circular surfaces of a vertically-oriented cylinder are labeled A. Electric field vector E points vertically upward, going up through the lower surface, up through the cylinder, and finally pointing up through the upper surface. The constant electric field E has magnitude 1.85 ✕ 103 N/C and is directed vertically upward, perpendicular to the cylinder's top and bottom surfaces so that no field...
1.2 A high cylinder with a cross-sectional area of ​​12.0 cm ^ 2 was partially filled...
1.2 A high cylinder with a cross-sectional area of ​​12.0 cm ^ 2 was partially filled with mercury whose density is 13.6 x 10^3 kg / m ^ 3; The surface of the mercury is at a height of 5.00 cm above the base of the cylinder. Water (1.00 x 10 ^ 3 kg / m ^ 3) is slowly poured over the mercury and it is observed that these two liquids do not mix. What volume of water should...
A cylinder of height 10 cm and cross sectional area of 1 cm2 is submerged inside...
A cylinder of height 10 cm and cross sectional area of 1 cm2 is submerged inside two immiscible liquids of specific gravity 1.1 and 1.0 respectively. The cylinder is in equilibrium in such a way that 5 cm of its height is submerged in the bottom liquid and 2 cm above the surface of the two liquids. In order the cylinder to be completely submerged inside the two liquids find the value of the mass of an object that needs...
A cylinder of 10-m-high, and a cross-sectional area of 0.1 m2 , has a piston (that...
A cylinder of 10-m-high, and a cross-sectional area of 0.1 m2 , has a piston (that is free to move) assumed to have negligible mass and thickness (see Figure 1(a)). Above the piston there is a liquid that is incompressible (constant density and volume) with ρliquid = 1000 kg/m3 . Below the piston there is air at 300 K, with a volume of 0.3 m3 . Assume air is an ideal gas (Ru =8.314 J.mol-1 .K-1 ; Mair = 28.9628...
A hydraulic lift in a garage has two pistons: a small one of cross-sectional area 4.50cm2...
A hydraulic lift in a garage has two pistons: a small one of cross-sectional area 4.50cm2 and a large one of cross-sectional area 220cm2 . There are two parts to this question please give CORRECT answer. Part A If this lift is designed to raise a 3400-kg car, what minimum force must be applied to the small piston? Part B If the force is applied through compressed air, what must be the minimum air pressure applied to the small piston?
Copper, brass and steel rods are welded to form a ?. The cross sectional area of...
Copper, brass and steel rods are welded to form a ?. The cross sectional area of each rod is 2.00 ??2. The free end of the copper rod is held at 100.0 ° ?; and the free ends of the brass and steel rods, at 0.0 ° ?. Suppose there is no heat loss from the sides of the rods, the lengths of which are: copper, 13.0 ??; brass, 18.0 ??; steel, 24.0 ??. a) What is the temperature of...
If the cross-sectional area of the manometer is 10 cm2 and the amount of water added...
If the cross-sectional area of the manometer is 10 cm2 and the amount of water added is 50 ml, what will be the height difference between the two arms of the manometer?
The length of a magnetic circuit of a relay is 25 cm and the cross-sectional area...
The length of a magnetic circuit of a relay is 25 cm and the cross-sectional area is 6.25 cm2. The length of the air-gap in the operated position of the relay is 0.2 mm. Calculate the magnetomotive force required to produce a flux of 1.25 mWb in the air gap. The relative permeability of magnetic material at this flux density is 200. Calculate also the reluctance of the magnetic circuit when the relay is in the unoperated position, the air-gap...
A silver wire has a cross sectional area A = 2.0 mm2. A total of 9.4...
A silver wire has a cross sectional area A = 2.0 mm2. A total of 9.4 × 1018 electrons pass through the wire in 3.0 s. The conduction electron density in silver is 5.8 × 1028 electrons/m3 and e = 1.60 × 10-19 C. What is the drift velocity of these electrons?
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT