Draw a PLC ladder logic diagram to simulate the operation of a sequential taillight system. The...

Draw a PLC ladder logic diagram to simulate the operation of a sequential taillight system. The light system consists of three separate lights on each side of the car. Each set of lights will be activated separately, by either the left or right turn signal switch. There is to be a 1-s delay between the activation of each light, and a 1-s period when all the lights are off. Ensure that when both switches are on, the system will not operate. Use the least number of timers possible. The sequence of operation should be as follows:

• The switch is operated.

• Light 1 is illuminated.

• Light 2 is illuminated 1 s later.

• Light 3 is illuminated 1 s later.

• Light 3 is illuminated for 1 s.

• All lights are off for 1 s.

• The system repeats while the switch is on

Expert Solution

SOLUTION:

PLEASE SIMULATE THIS LADDER DIAGRAM TO UNDERSTAND IT BETTER.

Manojponduru answered 11 months ago

draw a PLC ladder diagram for 5 floor elevator

-Explain step by step the operation of sequential logic circuit for traffic light ? digital system......

-Explain step by step the operation of sequential logic circuit for traffic light ? digital system... -Analyse the sequential logic circuit operation by using timing diagrams (with sketch for the diagrams) and present the optimization process of the sequential logic circuit. - Propose an enhancement for your design by using different sequential logic circuit. Please explain step by step with cleat hand writing.. Thanks.

Design a PLC ladder logic program to implement an automatic Car-Wash process. The system should have...

Design a PLC ladder logic program to implement an automatic Car-Wash process. The system should have a start and stop pushbuttons. When a Car enters the washing skid, a load cell switch is activated and the following sequence is performed automatically: 1. Soaping for (20) sec through soap nozzles 2. Washing for (120) sec using big brushes 3. Rinsing for (60) sec using water nozzles 4. Drying for (40) sec using air nozzles After finishing this process, the washing skid...

on plc program(PLC software) (Ladder diagram)basic program on paper is ok if it is drwan on...

on plc program(PLC software) (Ladder diagram)basic program on paper is ok if it is drwan on paper i just need an example to understand and do by myself detail answer is much appreciated thank you Write a short (no more than 2 page) paper on your process and ladder diagram • choose a simple manufacturing process (i.e. conveyor belt, garage door, filling operation, etc.) • process must have the following inputs • A safety factor (such as 2 pushbuttons or...

Design an elevator control system for an 8 floors building, draw the logic diagram, and illustrate...

Design an elevator control system for an 8 floors building, draw the logic diagram, and illustrate the system with the following situations: 1. The car is on the ground floor, John Doe wants to go from ground floor to 7th floor; 2. The car is on 8th floor, John Doe wants to go from 6th floor to the ground floor; 3. The car is moving up from 4th floor to 7th floor, John Doe wants to go from 6th floor...

Design a PLC ladder logic program to control a stop light. The program should have 3...

Design a PLC ladder logic program to control a stop light. The program should have 3 outputs: RED, YELLOW, and GREEN. The ladder logic should illuminate green for 60 seconds, then yellow for 10 seconds, then red for 60 seconds. The system should also have two sensor inputs: THROUGH_TRAFFIC and CROSS_TRAFFIC which detect when there is through traffic and cross traffic present. If through traffic is detected, and no cross traffic is detected, the system should maintain a green light...

5. a) Draw a state diagram for a sequential circuit that outputs a 1 if and...

5. a) Draw a state diagram for a sequential circuit that outputs a 1 if and only if its single input has completed the sequence 1111. b) Then build the circuit using D flip-flops and any necessary gates. NO Overlap is Allowed. 6. Repeat question 5 but this time OVERLAP IS ALLOWED:

Explain the similarities and differences between a Ladder Diagram, traditional binary logic, and computer code.

Use Omron PLC a) Create a ladder diagram (logical) that a bulb indicates when a box...

Use Omron PLC a) Create a ladder diagram (logical) that a bulb indicates when a box is filled with 10 items. b) Write (make) the programming (mnemonic) language c) Describe (write with your word) the sequence of operation of the system that you performed in part a and b.

Describe combinational and sequential logic

Question