Question

In: Civil Engineering

A solid steel bar with dimensions of 1 x 4 inches spans a 20 foot gap....

A solid steel bar with dimensions of

1

x

4

inches spans a 20 foot gap. The beam is loaded with a single 1000 lb load a

t

mid span.

Calculate the

deflection of the beam

at

every

foot along it

s length

.

(That is,

calculate

the deflecton

at x=0,

12,24, 36

...

inches) INCLUDE the weight of the beam. Plot the deflection, y, versus x

Expert Solution

Ally Wells answered 1 year ago

A steel shaft is to be manufactured either as a solid circular bar or as a...

A steel shaft is to be manufactured either as a solid circular bar or as a circular tube. The shaft is required to transmit a torque of 1200 N_m without exceeding an allowable shear stress of 40 MPa nor an allowable rate of twist of0.75°/m. (The shear modulus of elasticity of the steel is 78 GPa.). Determine the required outer diameter do of the solid shaft [58.8 mm] Determine the required diameter d2of the hollow shaft if thethickness t of...

A. What is the moment of inertia of a solid iron sphere 20 inches in diameter...

A. What is the moment of inertia of a solid iron sphere 20 inches in diameter about an axis passing through the sphere half way from its center to the surface (you will have to look up its density)? If the sphere rolls down an incline plane that makes an angle 20 degrees with the horizontal, what will be its acceleration? B. Derive the formula for acceleration of a circular disk that rolls down an inclined plane that makes an...

What is the moment of inertia of a solid iron sphere 20 inches in diameter about...

What is the moment of inertia of a solid iron sphere 20 inches in diameter about an axis passing through the sphere half way from its center to the surface (you will have to look up its density)? If the sphere rolls down an incline plane that makes an angle 20 degrees with the horizontal, what will be its acceleration? b. Derive the formula for acceleration of a circular disk that rolls down an inclined plane that makes an angle...

. [4 pts] The temperature of a 4 foot metal rod at a point x feet...

. [4 pts] The temperature of a 4 foot metal rod at a point x feet from its left endpoint is given by T(x) = 1 + 3x 2 , 0 ≤ x ≤ 4, where T is measured in degrees Celsius (and x is measured in feet). Find the average temperature of the rod. 5. [6 pts] A particle moves along a coordinate line and has an acceleration given by a(t) = 4t+ 6 cm/sec2 . If the particle’s...

Lab Procedure The cross-section dimensions of the 6061-T6 aluminum bar are 0.512 in x 0.248 in....

Lab Procedure The cross-section dimensions of the 6061-T6 aluminum bar are 0.512 in x 0.248 in. Attach the lead wires of the gages to the strain indicator as a quarter bridge circuit. (Note: the black and white lead wires are the common leads.) Enter the gage factor (GF=2.11) into the strain indicator. Record the specimen number (1, 2, or 3). Balance the strain indicator and note the zero readings. Load the specimen according to the table below and record the...

4. [30 pts] 20 liters of water at 20 bar and 100 °C are in a...

4. [30 pts] 20 liters of water at 20 bar and 100 °C are in a variable volume container. 56,000 kJ of heat are added to the system at constant pressure which causes an increase in both temperature and volume. a. [4 pts] Draw a schematic of the process b. [4 pts] Write the energy balance for this process and clearly state any assumptions: c. [12 pts] What is the final volume of the container? d. [8 pts] How much...

A 2024-T3 aluminum bar has rectangular cross section dimensions of 2" x 0.5". The length of...

A 2024-T3 aluminum bar has rectangular cross section dimensions of 2" x 0.5". The length of the column is 9.0 inches. A) Calculate the transition slenderness ratio (Sr)D for this column. [Answer should be 69.9] B) Calculate the slenderness ratio for your assigned column length. [Answer should be 62] C) Calculate the maximum unit load (Pcr/A) for the bar. Indicate whether the column is a Johnson or Euler column. [Numerical answer should be 25296 psi but I don't know Johnson...

3.7-4 A solid steel shaft ABC with diameter d=40 mm is driven at A by a...

3.7-4 A solid steel shaft ABC with diameter d=40 mm is driven at A by a motor that transmits 75kW to the shaft at 15 Hz. The gears at B and C drive machinery requiring power equal to 50kW and 25 kW, respectively. Compare the maximum shear stress and angle of twist in the shaft between the motor at A and the gear at C. Assume that G=75 GPa.

- Aluminum and Steel Samples Dog-bone shaped samples Thickness = .003 inches; Width = 4 mm;...

- Aluminum and Steel Samples Dog-bone shaped samples Thickness = .003 inches; Width = 4 mm; Length = 8 cm - Polycarbonate Plastic Samples Dog-bone shaped samples Thickness = .015 inches; Width = 4 mm; Length = 8 cm - iPod Wire Diameter = 1.2 mm for “thin”; Diameter = 2.0mm for “thick”; Length = 7 cm for both Calculate the stress (Force/Area) and strain (Elongation/Length) for all samples.

1)What is a sampling distribution for the sample mean, x-bar? Explain. Is x-bar a random variable?...

1)What is a sampling distribution for the sample mean, x-bar? Explain. Is x-bar a random variable? Why do you think so? 2) We learned standard error of the mean ( read sigma xbar in denotation) or standard deviation of sample mean. When the size(n) of the sample collected from a infinite population is greater than 1, why is the standard error of the mean smaller than the standard deviation of X, population ? Explain conceptually or/and algebraically. Think of formula for...