- Aluminum and Steel Samples Dog-bone shaped samples Thickness = .003 inches; Width = 4 mm;...

- Aluminum and Steel Samples

Dog-bone shaped samples Thickness = .003 inches; Width = 4 mm; Length = 8 cm

- Polycarbonate Plastic Samples

Dog-bone shaped samples Thickness = .015 inches; Width = 4 mm; Length = 8 cm

- iPod Wire Diameter = 1.2 mm for “thin”; Diameter = 2.0mm for “thick”; Length = 7 cm for both

Calculate the stress (Force/Area) and strain (Elongation/Length) for all samples.

Expert Solution

samet mamat answered 1 year ago

An annealed aluminum alloy slab with a thickness of 12 mm and width of 1m is...

An annealed aluminum alloy slab with a thickness of 12 mm and width of 1m is to be cold rolled to a thickness of 9 mm using 2-high rolls with roll diameter of 1m. The rolls have a coefficient of friction of 0.08 and they are rotating with a speed of 18 RPM. The aluminum has an entrance speed of 50 m/min and a width that does not change as a result of drawing. The strength coefficient K =240 and...

A parabolically shaped bookshelf has a width of 10 feet 8 inches at the top and...

A parabolically shaped bookshelf has a width of 10 feet 8 inches at the top and height 9 ft. 2 in.. Their are 7 rows of shelves with the same height. How tall is each shelf? How long is the board needed for the bottom of the shelf that is the fourth row of shelves from the bottom?

The sample measurements for Aluminum, Copper and Nylon have the same length, width, and thickness. While...

The sample measurements for Aluminum, Copper and Nylon have the same length, width, and thickness. While the length is 76.5mm and the width is 19.5mm, the thickness of these samples are about 0.127 mm. How might these specimens behave differently if they were thick?

In a sample of 100 steel canisters, the mean wall thickness was 8.1 mm with a...

In a sample of 100 steel canisters, the mean wall thickness was 8.1 mm with a standard deviation of 0.5 mm. Find a 95% lower confidence bound for the mean wall thickness. (Round the final answer to three decimal places.) The 95% lower confidence bound is

A copper pipe of diameter 3.5 cm and wall thickness 4 mm is used in an...

A copper pipe of diameter 3.5 cm and wall thickness 4 mm is used in an antibiotic factory to convey hot water a distance of 60 m at a flow rate of 20 L/s. The inlet temperature of the water is 90°C. Due to heat losses to the atmosphere, the outlet water temperature is 84°C. The ambient temperature is 25°C. The inside of the pipe is covered with a layer of fouling with a fouling factor of 7500 W/m2°C. What...

A solid steel bar with dimensions of 1 x 4 inches spans a 20 foot gap....

A solid steel bar with dimensions of 1 x 4 inches spans a 20 foot gap. The beam is loaded with a single 1000 lb load a t mid span. Calculate the deflection of the beam at every foot along it s length . (That is, calculate the deflecton at x=0, 12,24, 36 ... inches) INCLUDE the weight of the beam. Plot the deflection, y, versus x

3.7-4 A solid steel shaft ABC with diameter d=40 mm is driven at A by a...

3.7-4 A solid steel shaft ABC with diameter d=40 mm is driven at A by a motor that transmits 75kW to the shaft at 15 Hz. The gears at B and C drive machinery requiring power equal to 50kW and 25 kW, respectively. Compare the maximum shear stress and angle of twist in the shaft between the motor at A and the gear at C. Assume that G=75 GPa.

A specimen of concrete column (200 x 200 mm) of 1.5 m long with 4 steel...

A specimen of concrete column (200 x 200 mm) of 1.5 m long with 4 steel rebars (20 mm in diameter) inside with same length. If Ec = 21 Gpa, Es = 210 GPa, and free shrinkage strain = 0.0004, estimate the force carried by concrete and steel after shrinkage. If concrete tensile strength, ft = 5 MPa, will crack develop in this specimen?

Question