A rectangular beam of base b = 50 mm and height h = 25 mm is...

A rectangular beam of base b = 50 mm and height h = 25 mm is bent into a curved beam of 100 mm radius (R), and is subjected to a bending moment M of 500 N-m. Determine: The largest tensile and compressive stresses, how do the above values compare with the ones for straight beam?

Expert Solution

Ally Wells answered 1 year ago

A rectangular concrete beam of width b= 600 mm, is limited by architectural considerations to a...

A rectangular concrete beam of width b= 600 mm, is limited by architectural considerations to a maximum total depth h= 400 mm. It = 542 kN.m. Design the umust carry a total factored load moment Mflexural reinforcement for this member, using compression steel if necessary. Allow 75 mm to the center of the bars from the compression or tension face of the beam. Material strengths are ??′=27.6 ??? ??? ??=413 ?? ?. Select reinforcement to provide the needed areas, and...

Design of Rectangular Beams with Tension Reinforcement Design a rectangular beam section (i.e., select b, h,...

Design of Rectangular Beams with Tension Reinforcement Design a rectangular beam section (i.e., select b, h, and the required tension reinforcement) at midspan for a 22 ft-span simply supported beam that supports its own self-weight, a superimposed uniform dead load of 1.25 kip/ft, and a uniform live load of 2 kip/ft. The material properties are f 0 c = 4, 500 psi and fy = 60, 000 psi. Consider a clear cover of 1.5 inches to the #4 stirrups. Follow...

A rectangular beam has a width of 300 mm and an effective depth of 510 mm....

A rectangular beam has a width of 300 mm and an effective depth of 510 mm. It carries Vu = 200 KN and Mu = 55 KN-m and is reinforced with 2650 mm2. Use f’c = 21 MPa and fy = 345 MPa. Normal concrete. Express your answer in two decimal places. a. Compute the shear strength in KN provided by concrete using the less conservative formula as shown. Express your answer in two decimal places. b. Calculate the required...

A prestressed concrete beam with a rectangular sectin 120 mm wide by 300 mm deep supports...

A prestressed concrete beam with a rectangular sectin 120 mm wide by 300 mm deep supports a a live load of 3 kN/m. The spanning over 6 m is prestressed by a straight cable carrying an effective prestressing force of 200000 N located at an eccentricity of 55 mm, the density of concrete 24 kN/m3. Find : (1)- The resultant stress distribution for the centre of span cross section of the beam (2)- the presressing force which can balance the...

A rectangular beam 230 mm wide is subjected to the following at a section Ultimate bending...

A rectangular beam 230 mm wide is subjected to the following at a section Ultimate bending moment of 135 kn.m Ultimate shear force of 90 kn Use M25 grade of concrete and Fe 415 steel Design a suitable section and find the (flexural & shear) reinforcement required in the section.

The rectangular hollow section in this welded assembly has a height of h=73mm, a width of...

The rectangular hollow section in this welded assembly has a height of h=73mm, a width of w=48mm and a length L=592mm. For the weld in this assembly, calculate either the Unit second polar moment of Area or the Unit Second Moment of Area, whichever is required to determine the secondary shear stress for this weld loading condition. Provide your answer in m3.

You are shooting a rectangular target with width w and height h. Assume that hitting any...

You are shooting a rectangular target with width w and height h. Assume that hitting any point inside the rectangle is equally likely. Let X be the distance of the point you hit to the center of the rectangle. Find the PDF, CDF, mean and variance of X.

A wire of length L has a rectangular cross-section with height H and width W. The...

A wire of length L has a rectangular cross-section with height H and width W. The wire has a hole all the way through it of area a. The wire is made of material with constant resistivity ρ1 . A battery with a known voltage is applied across the ends of the wire. a. Find the electric field inside the material and the current flowing through the wire. b. If the hole is totally filled with a material that has...

A rectangular waveguide of width w and height h has cut-off frequencies for TE10 and TE11...

A rectangular waveguide of width w and height h has cut-off frequencies for TE10 and TE11 modes in the ratio 1 : 2. The aspect ratio ?

A disk is cast in an open mould with diameter 25 cm and height 15 mm....

A disk is cast in an open mould with diameter 25 cm and height 15 mm. The pouring temperature is 1200°C. Calculate the total heat evolved during cooling if the disk was cast in copper, and given that the heat of fusion is 200 kJ/kg.

Question