A rectangular beam 230 mm wide is subjected to the following at a section Ultimate bending...

A rectangular beam 230 mm wide is subjected to the following at a section
- Ultimate bending moment of 135 kn.m
- Ultimate shear force of 90 kn
- Use M25 grade of concrete and Fe 415 steel

Design a suitable section and find the (flexural & shear) reinforcement required in the section.

Expert Solution

Design of singly reinforced beam beam with given data is done with IS 456 code

Ally Wells answered 1 year ago

A beam is subjected to equal bending moments M = 6.5 kip-ft, as shown. The cross-section...

A beam is subjected to equal bending moments M = 6.5 kip-ft, as shown. The cross-section of the beam is also shown. The top rectangular area (1) has cross-section dimensions b1 x d1, as shown, where b1 = 6.5 in. and d1 =1.50 in. The left and right rectangular legs (2) and (3) are of dimensions b2 x d2 as shown, where b2=0.75 in. and d2=6.0 in. Determine: (a) the centroid location, the moment of inertia about the z axis,...

A prestressed concrete beam with a rectangular sectin 120 mm wide by 300 mm deep supports...

A prestressed concrete beam with a rectangular sectin 120 mm wide by 300 mm deep supports a a live load of 3 kN/m. The spanning over 6 m is prestressed by a straight cable carrying an effective prestressing force of 200000 N located at an eccentricity of 55 mm, the density of concrete 24 kN/m3. Find : (1)- The resultant stress distribution for the centre of span cross section of the beam (2)- the presressing force which can balance the...

A circular shaft, 100 mm diameter is subjected to combined bending moment and torque, the bending...

A circular shaft, 100 mm diameter is subjected to combined bending moment and torque, the bending moment being 3 times the torque. If the direct tension yield point of the material is 300 MN/m2 and the factor of safety on yield is to be 4, calculate the allowable twisting moment by the three following theories of failure: (a) Maximum principal stress theory (b) Maximum shear stress theory (c) Maximum shear strain energy theory.

1-. A concrete beam of rectangular cross section of size 300mm x 500 mm is prestressed...

1-. A concrete beam of rectangular cross section of size 300mm x 500 mm is prestressed with 750kN at an eccentricity of 100mm from the centre of gravity of the gross section with 500 mm2 of prestressing steel stress to 1500 N/mm2. Analyse the section for stress (find the stress in concrete at top and bottom fibre) 2- The same concrete is covering a span of 7m. It is subjected to live load of 20 kN/m. Evaluate the stresses at...

A rectangular beam has a width of 300 mm and an effective depth of 510 mm....

A rectangular beam has a width of 300 mm and an effective depth of 510 mm. It carries Vu = 200 KN and Mu = 55 KN-m and is reinforced with 2650 mm2. Use f’c = 21 MPa and fy = 345 MPa. Normal concrete. Express your answer in two decimal places. a. Compute the shear strength in KN provided by concrete using the less conservative formula as shown. Express your answer in two decimal places. b. Calculate the required...

A rectangular beam of base b = 50 mm and height h = 25 mm is...

A rectangular beam of base b = 50 mm and height h = 25 mm is bent into a curved beam of 100 mm radius (R), and is subjected to a bending moment M of 500 N-m. Determine: The largest tensile and compressive stresses, how do the above values compare with the ones for straight beam?

How calculation of moment of inertia will influence the bending stress value of a rectangular section?...

How calculation of moment of inertia will influence the bending stress value of a rectangular section? Also find the bending stress for a rectangular section of size 3500 mm X 650 cm in which the bending moment will be taken as 300x103 Nmm.

A rectangular concrete beam of width b= 600 mm, is limited by architectural considerations to a...

A rectangular concrete beam of width b= 600 mm, is limited by architectural considerations to a maximum total depth h= 400 mm. It = 542 kN.m. Design the umust carry a total factored load moment Mflexural reinforcement for this member, using compression steel if necessary. Allow 75 mm to the center of the bars from the compression or tension face of the beam. Material strengths are ??′=27.6 ??? ??? ??=413 ?? ?. Select reinforcement to provide the needed areas, and...

Design of Rectangular Beams with Tension Reinforcement Design a rectangular beam section (i.e., select b, h,...

Design of Rectangular Beams with Tension Reinforcement Design a rectangular beam section (i.e., select b, h, and the required tension reinforcement) at midspan for a 22 ft-span simply supported beam that supports its own self-weight, a superimposed uniform dead load of 1.25 kip/ft, and a uniform live load of 2 kip/ft. The material properties are f 0 c = 4, 500 psi and fy = 60, 000 psi. Consider a clear cover of 1.5 inches to the #4 stirrups. Follow...

A rectangular channel 10m wide carries a discharge of 40m3 /s. If at a section in...

A rectangular channel 10m wide carries a discharge of 40m3 /s. If at a section in this channel the depth is 1.5m, how far (upstream or downstream) from this section will the depth be 2.0m.Take So=0.00009and manning’s constant n=0.017.

Question