Question

In: Civil Engineering

Depth of flow at downstream of a hydraulic jump at a reservoir outlet is 7m. The...

Depth of flow at downstream of a hydraulic jump at a reservoir outlet is 7m. The downstream channel is rectengular with a bottom of 4m. The discharge rate is 135 m3/s and the change in elevation among all 3 cross-sections are negligible. Determine the height of sluice gate and depth of water in the reservoir at upstream of the sluice gate.

Solutions

Expert Solution

HAVE A NICE DAY


Related Solutions

The sequent depth, ys of a hydraulic jump in a rectangular channel is related to the...
The sequent depth, ys of a hydraulic jump in a rectangular channel is related to the initial yi, the discharge per unit length, q, gravity acceleration, g and density r. Express the ratio ys/yi in term of non-dimensional group and compare with the equation developed from momentum principles as shown below:                                                                                 ?! #              
Compute the wet area, wet perimeter, hydraulic radius and hydraulic depth for the trapezoidal channel section...
Compute the wet area, wet perimeter, hydraulic radius and hydraulic depth for the trapezoidal channel section with the following data: water depth = 5.5 ft, bottom width = 25 ft and side slopes 1:2.
Which of the following is NOT one of the four criteria by which the size of a hydraulic reservoir is determined?
Which of the following is NOT one of the four criteria by which the size of a hydraulic reservoir is determined?It must make allowance for dirt and chips to settle and air to escapeIts inner surface must be covered with a layer of stainless still to avoid corrosionIt must maintain oil level high enough to prevent a whirlpool effect at the pump inletIt must have a surface area large enough to dissipate heatAll of the aboveWhich of the following is...
a) Sketch the specific energy curves for the following open channel flows: · A hydraulic jump...
a) Sketch the specific energy curves for the following open channel flows: · A hydraulic jump formed in a rectangular open channel · Flow through a channel width constriction, where the depths remain subcritical throughout · Flow through a sluice gate, where the gate opening is less than the flow’s critical depth. · Flow through a combined channel width constriction together with an upward step, where the depth remains subcritical throughout. b) Define and explain the following terms · Critical...
A hydraulic jump is formed in a rectangular channel 6.5 ft wide. The conjugate depths are...
A hydraulic jump is formed in a rectangular channel 6.5 ft wide. The conjugate depths are 0.5 ft and 4.0 ft respectively. Calculate: a. specific discharge, b. energy lost in the jump, c. critical depth, minimum specific energy, d. Horsepower lost, e. Length of the jump and f. Classify the Jump.
Explain how to calculate depths, velocities, and headloss for a hydraulic jump. What is the difference...
Explain how to calculate depths, velocities, and headloss for a hydraulic jump. What is the difference between free and drowned outflow?
Which of the following is true about hydraulic jump? - A reduction in slope can cause...
Which of the following is true about hydraulic jump? - A reduction in slope can cause a hydraulic jump - in increase in manning's roughness can cause hydraulic jump - An increase in slope can cause a hydraulic jump - A smoother steeper channel will cause a hydraulic jump - A hydraulic jump results in a reduction of total head - A hydraulic jump results in an increase of total head
For a small scale hydraulic power system, the elevation difference between the reservoir water surface and...
For a small scale hydraulic power system, the elevation difference between the reservoir water surface and the pond water surface downstream of the reservoir is 20.35. The velocity of the water exhausting into the pond is 7 m/s, and the discharge through the system is 4 m3/s. The head loss due to friction in the penstock (inlet pipe to turbine, under very high pressure) is negligible. Find the power produced by the turbine in kilowatts. Assume specific weight of water...
A daredevil college professor wants to jump across a canyon of depth 100m and width 50m...
A daredevil college professor wants to jump across a canyon of depth 100m and width 50m on his motorcycle. He uses a ramp inclined at 60 degrees to cross the canyon.The other side of the canyon is 10m lower than his side. Find the Minimum velocity, vo, that his motorcycle should have to make it safely across the canyon. If he jumps with a velocity of vo/3 find out what (x,y) position he would crash
A radial flow hydraulic turbine whose design is based on a power specific speed,
A radial flow hydraulic turbine whose design is based on a power specific speed, Ωsp=1.707 is to produce 25 MW from a total head, HE=25 m. The overall turbine efficiency ηo=0.92, the mechanical efficiency is 0.985, and the loss in head in the nozzles is 0.5 m. The ratio of the blade tip speed to jet speed is 0.90. Assuming the meridional velocity is constant and equal to 10 m/s and there is no swirl in the runner exit flow,...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT