It´s applied an unit step of 10V on the input of a RC Series Circuit, it...

It´s applied an unit step of 10V on the input of a RC Series Circuit, it is known that resistor value is 1 Kohms, determine the value of the capacitor knowing that took it 10 seconds to charge it.

Solutions

Expert Solution

Manojponduru answered 6 months ago

Next > < Previous

Related Solutions

If the capacitor in an RC circuit is replaced by two identical capacitors connected in series,...

If the capacitor in an RC circuit is replaced by two identical capacitors connected in series, then find the CORRECT statement. Select one: a. The time constant will be tripled b. The time constant will decrease by a factor of 2 c. The time constant will be unchanged d. The time constant will decrease by a factor of 4 e. The time constant will be doubled

1. A simple RC circuit consists of a 1 microF capacitor in series with a 3,000...

1. A simple RC circuit consists of a 1 microF capacitor in series with a 3,000 ohm resistor connected to a 6V battery and an open switch. Initially the capacitor is discharged. Once the switch is closed, it determines the time it takes for the voltage in the sea 3.8 V capacitor. a. 3x10 ^ -8 s b. 3x10 ^ 9 s C. 3 s d. 0.003 s e. 3x10 ^ -9 s QUESTION 2 1. Three 8 ohm resistors...

Draw phasor diagrams for the following circuits. A) For the first circuit: Analyze a series RC...

Draw phasor diagrams for the following circuits. A) For the first circuit: Analyze a series RC circuit. So an emf with frequency w and peak voltage V connected in series to a resistance with peak voltage V_R and a capacitor with a peak votage V_C. B) For the second one, do a parallel RL circuit. Same emf as above, but resistance R in parallel to inductor with inductance L. Step by step Thank you

A series RC circuit with R = 5 W and C = 0.02 F is connected...

A series RC circuit with R = 5 W and C = 0.02 F is connected with a battery of E = 100 V. At t = 0, the voltage across the capacitor is zero. (a) Obtain the subsequent voltage across the capacitor. (b) As t → ∞, find the charge in the capacitor. (DIFFERENTIAL EQUATIONS) SOLVE THIS USING MATLAB SOLVE THIS USING MATLAB SOLVE THIS USING MATLAB SOLVE THIS USING MATLAB SOLVE THIS USING MATLAB SOLVE THIS USING MATLAB...

A series RC circuit is connected in parallel to a 5 volt DC voltage source, where...

A series RC circuit is connected in parallel to a 5 volt DC voltage source, where resistance R=1 M ohm and capacitance C= 1 microfarad. If at the start of operation, voltage across the capacitor is 5 volts, calculate the voltage across the capacitor at t=2 seconds. Also sketch the instantaneous voltage across the resistor. using differential equation.

Given a RC circuit in series , at time t=0, power supply 4v is connected to...

Given a RC circuit in series , at time t=0, power supply 4v is connected to the circuit causing charging of capacitor, determine at instant 8 seconds : Where C = 10 mF, R = 4 kOhms, and consider all initial values equal to ZERO. a) Tension on capacitor; b) Tension on resistor; c) total current.

Consider the circuit in (Figure 1). Suppose that vs = 10V

Consider the circuit in (Figure 1). Suppose that vs = 10V Part A Use voltage division to find the voltage across the 4 Ω resistor, positive at the top. Part B Use the result from part A and voltage division to find the voltage across the 9 Ω resistor, positive on the left.

A light bulb, a capacitor, and a nine-volt battery are wired up in series in a simple RC circuit.

A light bulb, a capacitor, and a nine-volt battery are wired up in series in a simple RC circuit. The light bulb has a resistance of 2.0 kΩ and the capacitor has a capacitance of 950 μF.(a) What is the electric current in the circuit at the exact moment the battery is connected (at t = 0)?(b) What is the electric current in the circuit 1 second after the battery was connected?(c) What is the electric current in the circuit...

Consider an RC circuit with resistance R and capacitance C. The circuit is stimulated with a...

Consider an RC circuit with resistance R and capacitance C. The circuit is stimulated with a pulse of amplitude A and width T. The purpose of this study is to understand what happens to the impulse response, capacitor voltage, and resistor voltage for various resistor values: 600 ?, 1000 ?, and 1200 ?. The name of the MATLAB script will be called project2a. Excite the circuit with a rectangular pulse voltage of amplitude=5 V and pulse width of 10 ms....

List out at least two uses for an RC circuit and explain how the RC would...

List out at least two uses for an RC circuit and explain how the RC would affect the use.

Subjects