3. A falling head permeability test is conducted on a sample of soil. The standpipe diameter...

3. A falling head permeability test is conducted on a sample of soil. The standpipe diameter = 5 mm, and the soil sample was cylindrical, 20 cm long by 10 cm in diameter. During the test, the initial head of water in the standpipe was 100 cm, and it dropped to 35 cm in 3 hours. a. Determine the coefficient of permeability, k, of the soil (cm/s). b. What soil type do you think this is?

Expert Solution

Ally Wells answered 1 year ago

A falling head permeability test was performed on a re-moulded silty clay soil sample 150 mm...

A falling head permeability test was performed on a re-moulded silty clay soil sample 150 mm in diameter and 250 mm in length. The diameter of the standpipe was 12.7 mm. At the start of the test, the height of the water in the standpipe measured 2,236 mm above the constant water level where the soil sample was immersed in. After 7 hours and 45 minutes, the height of the water in the standpipe was measured at 1971 mm. Determine:...

A falling-head permeameter containing a silty clay loam soil sample has a sample diameter of 10...

A falling-head permeameter containing a silty clay loam soil sample has a sample diameter of 10 cm, a falling-head tube of diameter 2 cm, and a sample length of 4 cm. If the initial head is 15 cm. It falls 4 cm over a period of 6 hours. (a) Find the hydraulic conductivity of the soil sample in m/s and ft/d. (b) What would be the hydraulic head after 12 hours? (c) How long would it take for the hydraulic...

1. What is the difference between the Constant Head and Falling Head Permeability Test? 2. What...

1. What is the difference between the Constant Head and Falling Head Permeability Test? 2. What principal are the two permeability tests based on? 3. Why would one use the falling head tests instead of the constant head test? 4. If you anticipate that the permeability of a soil is approximately 0.000001 cm/sec and the falling head permeability testing equipment had the following dimensions, how long should the test take if the beginning head is 20 cm and the final...

A cylindrical soil sample, 7.3 cm in diameter and 16.8 cm in height, is tested in...

A cylindrical soil sample, 7.3 cm in diameter and 16.8 cm in height, is tested in a constant-head permeability apparatus. A constant head of 75 cm is maintained during the test. After 1 minute of testing, a total of 945.7 gm of water was collected. The temperature was 20 oC. The void ratio of the soil was 0.43. Calculate the following: The hydraulic gradient The flow rate The discharge velocity The seepage force per unit volume The coefficient of permeability

a rotating bending test was conducted on a steel coupon with the thinnest diameter at 8.15mm...

a rotating bending test was conducted on a steel coupon with the thinnest diameter at 8.15mm load(kg) number of cycles test 1 22.5 30750 test 2 23.5 4750 test 3 29.7 5000 a) explain and describe the rotating bending test b) Describe the stress cycle that was used;

List & briefly explain any four parameters affecting coefficient of the permeability of soil.

A soil sample weighing 122g has diameter and length equal to 4.5 inches and 11 inches,...

A soil sample weighing 122g has diameter and length equal to 4.5 inches and 11 inches, respectively. The moisture content in soil came out to be 40 %. If specific gravity of soil solids is 2.67. Find Bulk unit weight, dry mass of sample, voids ratio, porosity, dry unit weight and degree of saturation of soil sample.

1. The turbine of a hydrostatic plant is driven by a falling head of water from...

1. The turbine of a hydrostatic plant is driven by a falling head of water from a falling head of water from a source 30 m high up through a 600 mm penstock flowing full. A. Evaluate the theoretical velocity of water as it hits the turbine blades in m/sec. B. Evaluate the theoretical discharge of water in m3/s. C.If the turbine is only 70% efficient, estimate the horsepower available from it.. 2. Reservoir A supplies water to a nozzle...

A test was conducted on a 4-stroke four cylinder engine having 6.9 cm diameter and 8.9...

A test was conducted on a 4-stroke four cylinder engine having 6.9 cm diameter and 8.9 cm stroke. The fuel supply to the engine is 0.065 kg/min. The B.P measurements are given below with constant engine speed of 300 rpm: With all cylinder firing = 16.9 kW Cut off at 1st cylinder = 8.46 kW Cut off at 2nd cylinder = 8.56 kW Cut off at 3rd cylinder = 8.6 kW Cut off at 1st cylinder = 8.46 kW If...

what are some failure types of unconfined compression test? how do sample disturbance and soil remolding...

what are some failure types of unconfined compression test? how do sample disturbance and soil remolding change the results of the unconfined compression test? and does the moisture content affect the unconfined compression strength and shear strength of clay?

Question