Question

In: Mechanical Engineering

At the beginning of compression of an ideal Diesel cycle the gas has a temperature and...

At the beginning of compression of an ideal Diesel cycle the gas has a temperature and pressure of 400C and 90 kN/m2, respectively. The volume ratio of compression is 16:1. The maximum temperature of the cycle is 14000C. Determine, for the cycle,

  1. the pressure and temperature at each of the cycle process change points,                            [8]
  2. the work done/kg gas,                                                                                                                           [4]
  3. the thermal efficiency,                                                                                                                           [4]
  4. the work ratio,                                                                                                                                         [3]
  5. the mean effective pressure,                                                                                                                [3]
  6. the Carnot efficiency within the cycle temperature limits.                                                           [3]

Take, γ=1.4 , cp = 1.004 kJ/kg K.

Solutions

Expert Solution

if you get doubt, please post it in comment section below.


Related Solutions

The compression ratio of an ideal air-powered Diesel cycle is 20. At the beginning of the...
The compression ratio of an ideal air-powered Diesel cycle is 20. At the beginning of the compression process, the pressure of the air is 100 kPa, the temperature is 20 ° C, and the highest temperature of the cycle is required not to exceed 2250 K. Show the cycle in the P-v diagram. Accept specific temperatures constant at room temperature. k=1.4 CP=1.005 kJ/kgK CV=0.718 kJ/kgK R=0.287 kJ/kgK a) Calculate the temperatures entering and leaving the cycle, the thermal efficiency of...
In an ideal standard dual cycle, the pressure and temperature at the beginning of compression are...
In an ideal standard dual cycle, the pressure and temperature at the beginning of compression are 1 bar and 47°C, respectively. The heat supplied in the cycle is 1250kJ/kg, two third of this heat is being added at constant volume and the remaining heat is added at constant pressure. If the compression ratio is 16, determine i. the maximum temperature in cycle ii. thermal efficiency of the cycle iii. the mean effective pressure
An ideal Otto cycle has a compression ratio of 7. At the beginning of the compression...
An ideal Otto cycle has a compression ratio of 7. At the beginning of the compression process, air is at 98 kPa, 30oC and 766 kJ/kg of heat is transferred to air during the constant-volume heat addition process. Determine (a) the pressure (p3) and temperature (T3) at the end of the heat addition process, (b) the net work output, (c) the thermal efficiency and (d) the mean effective pressure for the cycle. Use the IG model
An ideal Otto cycle has a compression ratio of 8. At the beginning of the compression...
An ideal Otto cycle has a compression ratio of 8. At the beginning of the compression process, air is at 95 kPa and 27°C, and 900 kJ/kg of heat is transferred to air during the constant-volume heat-addition process. Taking into account the variation of specific heats with temperature, determine (a) the pressure and temperature at the end of the heat-addition process, (b) the net work output, (c) the thermal efficiency, and (d) the mean effective pressure for the cycle
An ideal Otto cycle has a compression ratio of 8.5 At the beginning of the compression...
An ideal Otto cycle has a compression ratio of 8.5 At the beginning of the compression process, air is at 98 kPa and 27∘C, If the Tmax cannot exceed 2300K and 3e-5 kg of. assuming constant specific heats at ambient temperature, determine (a) the pressure and temperature at the end of each process. (b) the net work output, (c) the thermal efficiency, and (d) the mean effective pressure for the cycle.
An ideal Otto cycle has a compression ratio of 8. At the beginning of the compression...
An ideal Otto cycle has a compression ratio of 8. At the beginning of the compression process, air is at 95 kPa and 27°C, and 730 kJ/kg of heat is transferred to air during the constant-volume heat-addition process. Take into account the variation of specific heats with temperature. The gas constant of air is R = 0.287 kJ/kg·K. Determine: (a) the pressure and temperature at the end of the heat addition process (b) the net work output (c) the thermal...
The state at the beginning of compression of an air-standard Diesel cycle is fixed by p1...
The state at the beginning of compression of an air-standard Diesel cycle is fixed by p1 = 100 kPa and T1 = 310 K. The compression ratio is 18 and the cutoff ratio is 1.5. Determine: (a) the maximum temperature, in K. (b) the pressure at the end of the expansion, in kPa. (c) the net work per unit mass of air, in kJ/kg. (d) the percent thermal efficiency.
The state at the beginning of compression of an air-standard Diesel cycle is fixed by p1...
The state at the beginning of compression of an air-standard Diesel cycle is fixed by p1 = 100 kPa and T1 = 310 K. The compression ratio is 18 and the cutoff ratio is 1.5. Determine: (a) the maximum temperature, in K. (b) the pressure at the end of the expansion, in kPa. (c) the net work per unit mass of air, in kJ/kg. (d) the percent thermal efficiency
Assume you are working on an ideal gas-turbine cycle that has three stages of compression with...
Assume you are working on an ideal gas-turbine cycle that has three stages of compression with intercooling and three stages of expansion with reheating at 100 kPa and 290 K. This system uses a regenerator as well. The pressure ratio across each stage of the compressor and turbine is 3; the air temperature when entering the turbine is 1300 K; and the regenerator operates perfectly. Draw the T − s diagram of this system. Determine the mass flow rate of...
3. The compression ratio of the ideal air-powered diesel cycle is 14, while the cutting rate...
3. The compression ratio of the ideal air-powered diesel cycle is 14, while the cutting rate is 1.8.Since the air was initially at 100 kPa and 25 ° C; a. Pressure and temperature at the end of the heat transfer process b. Thermal efficiency c. Find the mean effective pressure (M.E.P).
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT