Question

In: Mechanical Engineering

To transmit 75 kW at 25 rev/s using 48 mm diameter shafting. The flanges are to...

To transmit 75 kW at 25 rev/s using 48 mm diameter shafting. The flanges are to be made of cast iron and keyed to the shafts, and power is transmitted from one flange to the other by a circle of fitted bolts (four are shown in the above figure but more or less bolts can be used). The adopted bolts must comply to the following technical specification: Property Class Designation: 4.6

Nominal size range: M5 – M100 (Sizes M5 to M45 are commonly used in construction)

Material and Treatment: Low or medium carbon steel

Tensile Ultimate Strength, 400MPa, Minimum.

Tensile Yield Strength, 240MPa, Minimum.

CALCULATE THE FOLLOWING

Key analysis,

Hub analysis

Flange (web) analysis

Bolt analysis.

Solutions

Expert Solution


Related Solutions

Diameter (mm) E. coli R/S Diameter (mm) S. aureus R/S Activity Range Oregano 27 54 Thyme...
Diameter (mm) E. coli R/S Diameter (mm) S. aureus R/S Activity Range Oregano 27 54 Thyme 26 54 Clove 14 18 Lavender 10 14 Sage 11 14 Chloramphenicol 14 27 Use the table to answer the following 6 questions about essential oils. Do essential oils appear to have the possibility of having some practical antibacterial use? Explain your reasoning. What could be some of the impracticalities and/or problems of using essential oils as an antibacterial agent given the information presented?...
A wheel of a diameter 180 cm is turning at 3.0 rev/s. Eventually it starts to...
A wheel of a diameter 180 cm is turning at 3.0 rev/s. Eventually it starts to slow down and when it does, time starts at t = 0s. From the moment it starts to slow down it stops after 26 revolutions. a) What is the wheel’s angular acceleration, in rad/s2? b) What is the time required to stop the wheel, from the moment it starts slowing down? c) What are the initial tangential speed and initial centripetal acceleration, at t...
Air at 25°C flows over a 10-mm-diameter sphere with a velocity of 20 m/s, while the...
Air at 25°C flows over a 10-mm-diameter sphere with a velocity of 20 m/s, while the surface of the sphere is maintained at 75°C. What is the rate of heat transfer from the sphere? q = ___ W ? Please provide correct final answer for guaranteed thumbs up rating !
A 30 m long pipe with an outside diameter of 75 mm is used to deliver...
A 30 m long pipe with an outside diameter of 75 mm is used to deliver steam at a rate of 2000 kg / hour. The vapor pressure is 198.53 kPa entering the pipe with a quality of 98%. The pipe needs to be given insulation with thermal conductivity of 0.2 W / (m K) so that the vapor quality only slightly decreases to 95%. The outer surface temperature of the insulation is assumed to be 25 ° C. Ignore...
A 500-loop circular armature coil with a diameter of 6.0 cm rotates at 190 rev/s in...
A 500-loop circular armature coil with a diameter of 6.0 cm rotates at 190 rev/s in a uniform magnetic field of strength 0.60 T . What is the rms voltage output of the generator? What would you do to the rotation frequency in order to double the rms voltage output? To double the output voltage, you must decrease by two times the rotation frequency. To double the output voltage, you must increase by four times the rotation frequency. To double...
Question 2 2.1       A brass rod of 25 mm in diameter is enclosed in a steel...
Question 2 2.1       A brass rod of 25 mm in diameter is enclosed in a steel tube. The tube is 10 mm thick with an outside diameter of 50 mm. The bar and the tube are initially 1 m long and are rigidly fastened together at each end. Calculate the stresses in the two materials when the temperature is raised by 80 0C.                                2.2       If the composite bar is then subjected to an axial tensile load of 60 kN, find...
A disk is cast in an open mould with diameter 25 cm and height 15 mm....
A disk is cast in an open mould with diameter 25 cm and height 15 mm. The pouring temperature is 1200°C. Calculate the total heat evolved during cooling if the disk was cast in copper, and given that the heat of fusion is 200 kJ/kg.
Question 2 2.1       A brass rod of 25 mm in diameter is enclosed in a steel...
Question 2 2.1       A brass rod of 25 mm in diameter is enclosed in a steel tube. The tube is 10 mm thick with an outside diameter of 50 mm. The bar and the tube are initially 1 m long and are rigidly fastened together at each end. Calculate the stresses in the two materials when the temperature is raised by 80 0C.                                2.2       If the composite bar is then subjected to an axial tensile load of 60 kN, find...
A 75‐mm‐diameter orifice with D and D/2 taps is used to measure the flow rate of...
A 75‐mm‐diameter orifice with D and D/2 taps is used to measure the flow rate of 65°C water in a 150‐mm‐ID pipe. Determine the pressure difference for a flow rate of 20 L/s
An odd-shaped object rotates at a speed of 10.0 rev/s. A small 25 g mass with...
An odd-shaped object rotates at a speed of 10.0 rev/s. A small 25 g mass with moment of inertia I=1.5x10-6 kg·m2 is dropped onto the object at a distance of 4.5 cm from its center of mass. The odd-shaped object slows to a speed of 9.0 rev/s. What is the moment of inertia of the odd-shaped object?
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT