Question

In: Electrical Engineering

How to Design amplifier circuit that has a gain of 1000 to 1500. And apply it...

How to Design amplifier circuit that has a gain of 1000 to 1500. And apply it on multisim.

Solutions

Expert Solution

You can design an amplifier with a voltage gain of 1000 or 1500 by using an operational amplifier. An inverting amplifier is shown in the figure below.

Voltage gain of this amplifier is given as

It can be seen that voltage gain depends on the ratio of the resistors, therefore, by maintaining proper ratio, we can achieve whatever gain we wants. For eg, to get a voltage gain of 1000, we need

or

Let's choose

then

So the following circuit will give you the gain of 1000

You can proceed in the same way to obtain any voltage gain. These op-amp ICs are reliable as well as cheap. Remember, if your amplifier is going in saturation, decrease the input.

Here is the multisim simulatiion circuit

Here is the Oscilloscope screen , which is showing gain of 1000, Red one is input and blue one is output. Input is in channel A while output is in channel B

Please thumbs me up, if my suggestions helped you, Thankyou


Related Solutions

Operational amplifier question Design a non- inverting amplifier with gain of 7.5?
Operational amplifier question Design a non- inverting amplifier with gain of 7.5?
Design a differential amplifier, in Multisim, with a gain of 10000 by cascoding the differential stage...
Design a differential amplifier, in Multisim, with a gain of 10000 by cascoding the differential stage of the circuit. Please show parameters used
Suppose that you design an amplifier circuit but measuring the output on the oscilloscope shows that...
Suppose that you design an amplifier circuit but measuring the output on the oscilloscope shows that it is just oscillating wildly. List the first three things to check to understand what is causing the oscillation.
Explain the operation of the isolation amplifier. Design a circuit that takes an input voltage and...
Explain the operation of the isolation amplifier. Design a circuit that takes an input voltage and outputs a scaled differentiated version of the input minus a scaled version of the input, at the output of the circuit
2. About amplifiers: (i) Draw/Project a circuit using an operational amplifier with gain -100 (ii) What...
2. About amplifiers: (i) Draw/Project a circuit using an operational amplifier with gain -100 (ii) What is the cutoff frequency of the amplifier in question (i) if we used an operational amplifier 741? (iii) What configuration (inverter or non-inverter) is most vulnerable to finite CMRR ( Common Mode Rejection Ratio )? (iv) Draw an instrumentation amplifier and calculate its literal equation of the gain
Design a differentiator circuit using a capacitor to have gain of 100. What is the output...
Design a differentiator circuit using a capacitor to have gain of 100. What is the output of the amplifier if the input is Vin = 0.05 sin 500.
Draw a circuit diagram of the differential amplifier with two Rcs.
Draw a circuit diagram of the differential amplifier with two Rcs.
Write a literature survey about DC power supply circuit and audio amplifier circuit to preform a...
Write a literature survey about DC power supply circuit and audio amplifier circuit to preform a speaker?
Design a common-emitter amplifier that has a dc input value of 15v and that meets the...
Design a common-emitter amplifier that has a dc input value of 15v and that meets the following requirements 1. a gain of at least 80 2. low frequency -3dB less than 100Hz
0. We are designing an ECG circuit that has three parts, including (1) Instrumentation Amplifier (2)...
0. We are designing an ECG circuit that has three parts, including (1) Instrumentation Amplifier (2) High-pass filter (3) Low-pass filter. Each part should have the gain of 10, so the entire circuit should have the gain of 1000. We will add a LED driver at the end to be lit when detecting heartbeat. Design 1. Design a differential amplifier with the gain equal to one and use 10k? for its feedback resistor. Calculate the resistor value on the non-inverting...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT