Design a differentiator circuit using a capacitor to have gain of 100. What is the output...

Design a differentiator circuit using a capacitor to have gain of 100. What is the output of the amplifier if the input is Vin = 0.05 sin 500.

Expert Solution

Manojponduru answered 2 years ago

2. About amplifiers: (i) Draw/Project a circuit using an operational amplifier with gain -100 (ii) What...

2. About amplifiers: (i) Draw/Project a circuit using an operational amplifier with gain -100 (ii) What is the cutoff frequency of the amplifier in question (i) if we used an operational amplifier 741? (iii) What configuration (inverter or non-inverter) is most vulnerable to finite CMRR ( Common Mode Rejection Ratio )? (iv) Draw an instrumentation amplifier and calculate its literal equation of the gain

What is the maximum charge on a capacitor in an RC circuit? As the capacitor in...

What is the maximum charge on a capacitor in an RC circuit? As the capacitor in an RC circuit charged, what is the current as a function of time?Explain your answer physically. 1.5 V batteries are usually connected in series. Would the batteries last longer or shorter if they were connected in parallel instead?

Design a Moore sequential circuit that has an input X and an output Y. The circuit...

Design a Moore sequential circuit that has an input X and an output Y. The circuit detects the following sequence: 100 Your answer should include state diagram and state table. Hint. X= 0 1 0 1 0 0 0 1 1 1 0 0 1 0 1 Y= 0 0 0 0 0 1 0 0 0 0 0 1 0 0 0

How to Design amplifier circuit that has a gain of 1000 to 1500. And apply it...

How to Design amplifier circuit that has a gain of 1000 to 1500. And apply it on multisim.

Design a circuit where the voltage across the capacitor matches the input step function as closely...

Design a circuit where the voltage across the capacitor matches the input step function as closely as possible. Sketch/show a picture of your result and which circuit parameters (R and C you used). Explain why the output looks like it does. Design a circuit where the voltage across the capacitor looks like a triangle wave (each peak looks like a triangle). Sketch/show a picture of your result and which circuit parameters (R and C you used). Explain why the output...

Suppose that you design an amplifier circuit but measuring the output on the oscilloscope shows that...

Suppose that you design an amplifier circuit but measuring the output on the oscilloscope shows that it is just oscillating wildly. List the first three things to check to understand what is causing the oscillation.

design an electro- pneumatic circuit with three cylinder output .the process will be in sequence the...

design an electro- pneumatic circuit with three cylinder output .the process will be in sequence the cylinder 1 extend , cylinder 2 then cylinder 3(using Timers). draw the pneumatic circuit including directional control valve and cylinders etc.. draw the electric circuit of pneumatic circuit including switches, relays , timer etc.. if possible include the conveyor motor in electric circuit.

1) design a circuit that output is generated based on the control signals Inputs are A1,...

1) design a circuit that output is generated based on the control signals Inputs are A1, A0 and B1, B0 C1 C0 Output 0 0 add 0 1 subtract 1 0 AND 1 1 EXOR 2) Design a 5 by 32 decoder using 3 by 8 or smaller decoders

Please use a transformer, bridge full-wave rectifier and filter capacitor to design a power supply circuit...

Please use a transformer, bridge full-wave rectifier and filter capacitor to design a power supply circuit that converts 60Hz-110V AC to 12V DC. Please (1) draw a circuit diagram, (2) calculate the value of the filter capacitor C so that the ripple at the output current of 2A needs to be less than 0.1V, (3) select the transformer output voltage and estimate the peak voltage of the DC power supply.

2. You are an engineer trying to design a capacitor. You have a parallel-plate capacitor made...

2. You are an engineer trying to design a capacitor. You have a parallel-plate capacitor made of two circular metal plates. The radius of each plate is 1 m and they are separated by a distance of 0.1 mm. If the space in between the plates was filled with vacuum, the capacitor would have a capacitance of 0.278 μF but you want to make this capacitor have a capacitance of 1.0 μF. You only have paraffin (K=2.2) and glass (K=5)...

Question