Question

In: Mechanical Engineering

I have a 6,000 lb truck. If I have a 4” hydraulic cylinder and want the...

I have a 6,000 lb truck. If I have a 4” hydraulic cylinder and want the truck to raise 6ft in 3 seconds, what size drive motor and pump do I need?The prime mover should spin at 1800 rpm.

pump displacement, RPM and Prime Mover horse power, not physical dimentions

Solutions

Expert Solution


Related Solutions

How factor safety is important in design of hydraulic cylinder?
How factor safety is important in design of hydraulic cylinder?
Draw a simple circuit to open and close a double acting hydraulic cylinder.
Draw a simple circuit to open and close a double acting hydraulic cylinder.
I have a 50cc of hydraulic motor, accumulator pressure at 40MPa at max, with 10MPa at...
I have a 50cc of hydraulic motor, accumulator pressure at 40MPa at max, with 10MPa at precharge. How can i determine what pump sizing will i use for hydraulic hybrid purpose.
08-5 Calculate and compare the hydraulic and TSS loadings (lb/d) from wastewater and stormwater for a...
08-5 Calculate and compare the hydraulic and TSS loadings (lb/d) from wastewater and stormwater for a 10-acre urban neighborhood. Assume the following: *Wastewater: 5 houses/acre; 3.5 people/house; 50 gal/person/day; TSS = 200 mg/L *Stormwater: 0.75 inch rainfall over 24 hours, 50% of rainfall runs off; TSS = 60 mg/L Answer: WW load = 875 gpd, 14.6 lb/d; SW load = 101,820 gal/d, 51.0 lb/d
A hydraulic press for compacting powdered samples has a large cylinder which is 10.0 cm in...
A hydraulic press for compacting powdered samples has a large cylinder which is 10.0 cm in diameter, and a small cylinder with a diameter of 2.0 cm. A lever is attached to the small cylinder as shown in (Figure 1) . The sample, which is placed on the large cylinder, has an area of 4.0 cm2. What is the pressure on the sample if F = 320N is applied to the lever? Express your answer to two significant figures and...
Find the work (in ft-lb) required to pump all the water out of a cylinder that...
Find the work (in ft-lb) required to pump all the water out of a cylinder that has a circular base of radius 6 ft and height 200 ft. Use the fact that the weight-density of water is 62.4 lb/ft3. Find the work (in ft-lb) required to pump all the water out of the cylinder if the cylinder is only half full.
Investment A: Year: 0 1 2 3 4 5 Cash flow: -$14,000 $6,000 $6,000 $6,000 $6,000...
Investment A: Year: 0 1 2 3 4 5 Cash flow: -$14,000 $6,000 $6,000 $6,000 $6,000 $6,000 Investment B: Year: 0 1 2 3 4 5 Cash flow: -$15,000 $7,000 $7,000 $7,000 $7,000 $7,000 Investment C: Year: 0 1 2 3 4 5 Cash flow: -$18,000 $12,000 $4,000 $4,000 $4,000 $4,000 The cash flows for three projects are shown above. The cost of capital is 7.5%. If an investor decided to take projects with a payback period two years or...
A hydraulic press for compacting powdered samples has a large cylinder which is 10.0 cm in diameter
A hydraulic press for compacting powdered samples has a large cylinder which is 10.0 cm in diameter, and a small cylinder with a diameter of 2.0 cm. A lever is attached to the small cylinder as shown in (Figure 1). The sample, which is placed on the large cylinder, has an area of 4.0 cm2. What is the pressure on the sample if F = 320N is applied to the lever? Express your answer to two significant figures and include the appropriate units.
On January 1, Delivery, Inc. purchased a truck for $67,500 with a $6,000 salvage value and...
On January 1, Delivery, Inc. purchased a truck for $67,500 with a $6,000 salvage value and a four-year life. The company used the straight-line method of depreciation. The truck was sold on December 31, Year 2 for $22,500. Which of the following is one effect of recording the truck sale in the accounting records? Select one: A. The Truck account is reduced by $33,000. B. The Accumulated Depreciation account is reduced by $30,750. C. A loss of $45,000 is recognized....
The question I have is that I want to draw without having to drag and then...
The question I have is that I want to draw without having to drag and then clicking the button whether I want a line or rectangle. It should work first by hitting either the line or rectangle button and then making a drag on the panel with mouse, then after releasing the drag it creates the graphic. Here is my current code. package Mod1; import java.awt.*; import java.awt.event.*; import javax.swing.*; class paintGUI extends JComponent { // Image in which we're...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT