Question

In: Mechanical Engineering

in depth review into elastic and electromagnetic hysteresis of steel

in depth review into elastic and electromagnetic hysteresis of steel

Solutions

Expert Solution


Related Solutions

Q11 a) How is hysteresis detected in instruments? b) Illustrate the effect of hysteresis on an...
Q11 a) How is hysteresis detected in instruments? b) Illustrate the effect of hysteresis on an instrument. c) What is an instruments’ span?
A steel has a modulus of elasticity of 29,000 ksi and an elastic limit of 52...
A steel has a modulus of elasticity of 29,000 ksi and an elastic limit of 52 210 psi. A rod of this material and cross section of 0.0186 in2 and 36 in length is fastened vertically to a beam with a load of 410 lb at the opposite end. Determine: a) If this load is removed, will the bar return to its initial length? Justify the answer; b) The unitary deformation of the bar in these conditions; c) The minimum...
Calculate the flow depth in a rectangular riveted steel open channel with a width of 6.1...
Calculate the flow depth in a rectangular riveted steel open channel with a width of 6.1 m and a slope of 0.0001, since the water flow is 6.8 m3/s.
In-depth please explain the peer-review process, all steps, for publishing in BIOLOGY.
In-depth please explain the peer-review process, all steps, for publishing in BIOLOGY.
The output shaft of a 120 Watt electric motor has a 20° full-depth steel spur pinion...
The output shaft of a 120 Watt electric motor has a 20° full-depth steel spur pinion with 20 teeth and a module of 2.5 mm driving a 36-tooth gear attached to an air blower. The pinion speed is 100 rpm. Both the pinion and gear are manufactured from grade 2 steel using hobs shaping cutters, have a 18mm wide face, through-hardened steel at 200 Brinell, and are aligned in service such that kH = 1.6. For a service life of...
Using LRFD, select a 30-ft-long W section of A992 steel with a nominal depth of 10...
Using LRFD, select a 30-ft-long W section of A992 steel with a nominal depth of 10 in (a W12) to support a tensile service dead load PD=130kand a tensile service live load PL=110k. In addition, the section is to comply with the slenderness ratio limit from AISC D1 to prevent sag of the member. As shown in the figure below, the member is to have two lines of bolts in each flange for 7/8-in bolts (at least three in a...
Please review (in depth) the court case of United States vs. Microsoft. Please list the facts...
Please review (in depth) the court case of United States vs. Microsoft. Please list the facts of the case, results and reasoning. Thank you.
Parameter Steel . Modulus of Elasticity 30,000,000 psi Proportional/Elastic Limit 34,000 psi Allowable Bending Stress 24,000...
Parameter Steel . Modulus of Elasticity 30,000,000 psi Proportional/Elastic Limit 34,000 psi Allowable Bending Stress 24,000 psi Allowable Axial (C or T) Stress 24,000 psi Allowable Shear Stress 16,500 ps You have a 25-foot long, simply supported W12-50 steel beam. It is supporting a single 10,000# point load at its midpoint. Including the weight of the beam, answer the questions below: A. What is the maximum bending moment (foot-#) and resulting maximum bending stress (psi)? Is this allowable? B. What...
Electromagnetic Induction
We are rotating a 2 m long metallic rod with an angular frequency of 200 rad/s with an axis normal to the rod passing through its one end. And on to the other end of the rod, it is connected with a circular metallic ring. There exist a uniform magnetic field of 1.5 T which is parallel to the axis everywhere. Find out the emf induced between the centre and the ring?
pick one of the following to drscribe fully: hysteresis, rational expectations or quantitative easing
pick one of the following to drscribe fully: hysteresis, rational expectations or quantitative easing
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT