A simple pin-connected truss is loaded and supported as shown in the figure.

A simple pin-connected truss is loaded and supported as shown in the figure. The load P is 200 kN. All members of the truss are aluminum pipes that have an outside diameter of 115 mm and a wall thickness of 6 mm. Determine the normal stress in each truss member. Assume truss dimensions of a = 12.0 m, b = 7.5 m, and c = 6.0 m.

Expert Solution

Amanda K answered 2 years ago

Rigid bar ABC shown in Figure P1.30 is supported by a pin at bracket A and by tie rod (1).

Rigid bar ABC shown in Figure P1.30 is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 5 mm, and it is supported by double-shear pin connections at B and D. The pin at bracket A is a single-shear connection. All pins are 7 mm in diameter. Assume a = 600 mm, b = 300 mm, h = 450 mm, P = 900 N, and θ = 55°. Determine the...

As shown, the truss is loaded by the forces P1P1P_1 = 425 NN and P2P2P_2 =...

As shown, the truss is loaded by the forces P1P1P_1 = 425 NN and P2P2P_2 = 865 NN and has the dimension aaa = 1.10 mm .sing the method of joints, determine FABFABF_AB, FBCFBCF_BC, and FBDFBDF_BD, the magnitude of the force in each of the members connected to joint B. Assume for your calculations that each member is in tension, and include in your response the sign of each force that you obtain by applying this assumption

Four resistors are connected to a battery as shown in the figure. The current in the...

Four resistors are connected to a battery as shown in the figure. The current in the battery is I, the battery emf is ? = 6.20 V, and the resistor values are R1 = R, R2 = 2R, R3 = 4R, R4 = 3R. Find the voltages across each resistor. R 1, R2 and R3 are in series. R4 is in parallel.

A pin-ended chord of a truss is treated as a member in a braced frame. Its...

A pin-ended chord of a truss is treated as a member in a braced frame. Its length is 12 ft. It must carry a tension dead load of 95 kips and live load of 180 kips along with a uniformly distributed transverse dead load of 1.2 kips/ft and live load of 2.3 kips/ft. Will a W8x67, A992 member be adequate if the transverse load is applied to put the bending about the strong axis? Determine by (a) LRFD and (b)...

The structure of the figure is supported by the pin A of diameter d=3/4" and a cable that passes through the pulley of negligible diameter D.

The structure of the figure is supported by the pin A of diameter d=3/4" and a cable that passes through the pulley of negligible diameter D.pulley of negligible diameter D and whose assembly is shown in the figure. For the CE bar it was necessary to construct it by joining two sections of plate with a welded joint in the form of a thorn.herringbone welded joint, as shown in the detail. For this configuration, determinea. The minimum area of the...

The composite shaft shown in the figure consists of two steel pipes that are connected at...

The composite shaft shown in the figure consists of two steel pipes that are connected at flange B and securely attached to rigid walls at A and C. Steel pipe (1) has an outside diameter of 158 mm and a wall thickness of 6 mm. Steel pipe (2) has an outside diameter of 114 mm and a wall thickness of 4 mm. Both pipes are 3.5 m long and have a shear modulus of 80 GPa. If a concentrated torque...

The spring-loaded piston–cylinder device shown in the figure is filled with 0.55 kg of water vapor...

The spring-loaded piston–cylinder device shown in the figure is filled with 0.55 kg of water vapor that is initially at 4 MPa and 400°C. Initially, the spring exerts no force against the piston. The spring constant in the spring force relation F = kx is k = 0.9 kN/cm and the piston diameter is D = 20 cm. The water now undergoes a process until its volume is one-half of the original volume. Calculate the final temperature and the specific...

Consider three gas connected gas containers as shown in the figure below. Consider three gas connected...

Consider three gas connected gas containers as shown in the figure below. Consider three gas connected gas containers as shown in the figure below. CO2 (g) P = 2.13, V = 1.50L H2(g) P = 0.861 atm, V = 1.00 L Ar (g) p = 1.15atm, V = 2.00L T = 298K Assume, that you open the two stopcock so that the gases can flow freely. Calculate the change of the chemical potential of the entire system due to mixing...

Two balls connected by a rod, as shown in the figure below (Ignore rod’s mass).

Two balls connected by a rod, as shown in the figure below (Ignore rod’s mass). Mass of ball X is 8kg and the mass of ball Y is 5 kg What is the moment of inertia of the system about AB?

Q1 Five capacitors are connected across a potential difference Vab as shown in Figure. Because of...

Q1 Five capacitors are connected across a potential difference Vab as shown in Figure. Because of the dielectrics used, each capacitor will break down if the potential across it is V=61 V. What should be the value of Vab (with one decimal place) if you reach the break down voltage one of the capacitor. Q2 Suppose after charging a 3.7

Question