Air flows through a pipe that has a length of 45 m with an inside diameter...

Air flows through a pipe that has a length of 45 m with an inside diameter of 0.025 m. The Mach number of the flow exiting the pipe is 0.26, with a static pressure of 1 atmosphere and a temperature of 300 K. If the friction factor is assumed constant at 0.007, calculate the Mach number, static pressure, static temperature and total pressure at the entrance.

Expert Solution

samet mamat answered 2 years ago

Air flows down a pipe with a diameter of 0.15 m. At the inlet to the...

Air flows down a pipe with a diameter of 0.15 m. At the inlet to the pipe, the Mach number is 0.1, the pressure is 70 kPa, and the temperature is 35°C. If the flow can be assumed to be adiabatic and if the mean friction factor is 0.005, determine the length of the pipe if the Mach number at the exit is 0.6. Also, find the pressure and temperature at the exit to the pipe.

1)10 m3 /h of water flows through a pipe with 100 mm inside diameter. Calculate the...

1)10 m3 /h of water flows through a pipe with 100 mm inside diameter. Calculate the flow velocity inside this pipe. ? 2) A river discharges 100 m3 of water to the sea every 2 seconds. What is the flow-rate of this river expressed in m3/s?

a- Water enters a house through a pipe with inside diameter of 3.0 cm at an...

a- Water enters a house through a pipe with inside diameter of 3.0 cm at an absolute pressure of 5.0 X 105 Pa. A 1.5 cm diameter pipe leads to the second-floor bathroom 6.0 m above. When the flow speed at the inlet pipe is 2.0 m/s find: - Flow speed (velocity) of the water in the bathroom - Pressure water in the bathroom? - Calculate the volume flow rate in the bathroom.

Water flows through a cast iron pipe with a diameter of 30 mm. The pipe is...

Water flows through a cast iron pipe with a diameter of 30 mm. The pipe is inclined at an angle of 3 degrees from horizontal and is 40 m long. The water flows due to gravity only. What is the maximum volume flow rate of the water? You may ignore any minor loses.

Air flows through a 0.25-m-diameter duct. At the inlet the velocity is 300 m/s, and the...

Air flows through a 0.25-m-diameter duct. At the inlet the velocity is 300 m/s, and the stagnation temperature is 90°C. If the Mach number at the exit is 0.3, determine the direction and the rate of heat transfer. For the same conditions at the inlet, determine the amount of heat that must be transferred to the system if the flow is to be sonic at the exit of the duct.

Air at 80oC flows through a packed bed of cylinders with effective diameter of 0.015 m...

Air at 80oC flows through a packed bed of cylinders with effective diameter of 0.015 m and length the same as the diameter. The bed void fraction is 0.40 and the length of the packed bed is 2 2 m. The air enters the bed at 1.3 atm abs at the rate of 2.45 kg/m .s. Calculate the pressure drop of air in the bed

Air flows in a pipe with a diameter, D=50 mm. The inlet conditions are: M1 =...

Air flows in a pipe with a diameter, D=50 mm. The inlet conditions are: M1 = 3; total pressure, P01 = 1000 kPa absolute; and temperature, T1 = 550 K. The friction coefficient is, f = 0.004. The exit Mach number decreases with the length of the pipe. Plot the following while the exit Mach number to be changed from 2.5 to 0.99 with decrements of ?M=0.01: a) L, length of the pipe that is going to give the desired...

Consider a pipe (diameter of 50 mm) with air flowing through it. The inlet conditions are:...

Consider a pipe (diameter of 50 mm) with air flowing through it. The inlet conditions are: Mach 3; total pressure = 1000 kPa and 550 K. The friction coefficient (f) is 0.004. The exit Mach number decreases with the length of the pipe. Assume adiabatic, steady flow. Write a short Matlab code and plot the following, while the exit Mach number changes from 2.5 to 0.99 with increments of ?M=0.01. Find the length of the pipe that is going to...

Water flows upward and then is discharged to the right through a 3 inch diameter pipe...

Water flows upward and then is discharged to the right through a 3 inch diameter pipe elbow, at a steady flow rate of 1 cubic foot per second, the gage pressure at the entrance to the elbow is 30 psi. What vertical and horizontal force is necessary to hold the elbow stationary, neglecting any required torque.

A 8.0-cm-diameter horizontal pipe gradually narrows to 5.0 cm . When water flows through this pipe...

A 8.0-cm-diameter horizontal pipe gradually narrows to 5.0 cm . When water flows through this pipe at a certain rate, the gauge pressure in these two sections is 31.0 kPa and 25.0 kPa , respectively. What is the volume rate of flow?

Question