Sketch constant preassure curve in T-s diagram.

Expert Solution

The constant pressure and constant volume processes are given by curved lines on t-s diagram and the slope of constant volume process is greater than constant pressure on a t-s plot.

As we can see from the above figure that -

(1) On heat addition process the temperature increases and so does the entropy.

(2) On heat rejection process the temperature decreases and so does the entropy.

Which means that the temperature and entropy are the properties that are associated with the heat changes that take place in a system.

PLEASE UPVOTE.......!

samet mamat answered 2 years ago

For each problem, sketch the appropriate process diagram on a T-v, P-v or P-h diagram 1)...

For each problem, sketch the appropriate process diagram on a T-v, P-v or P-h diagram 1) Oil enters the outer tube of an insulated concentric tube heat exchanger at a temperature of 500k, and exits at a temperature of 400k. The mass flow rate of the oil is 5 kg/s, and the oil has a specific heat of Cp=1.91 kJ/kg*K. Saturated liquid water at 100 degrees celsius enters the inner tube, and exits at 100 degrees celsius with a quality...

For each problem, sketch the appropriate process diagram on a T-v, P-v, or P-h diagram 4.60...

For each problem, sketch the appropriate process diagram on a T-v, P-v, or P-h diagram 4.60 : Steam exiting the turbine of a power plant passes through the insulated shell-and-tube heat exchanger condenser. The mass flow rate of the steam is 145 kg/s, and the steam enters the heat exchanger as a saturated mixture with a quality of 0.95 at 20 kPa. The steam exits the condenser as a saturated liquid at 20 kPa. Liquid cooling water is used to...

Sketch the curve given by the parametric equation x= tan(t) , y=sec (t) for -pi/2 <...

Sketch the curve given by the parametric equation x= tan(t) , y=sec (t) for -pi/2 < t < pi/2. Eliminate the parameter "t" and find the Cartesian form of this curve. What type of curve is this? What curve would be good if "t" belong to the interval (pi/2, 3pi/2)?

3. Sketch a T-v diagram and find the specified state for the following states a. Propane...

3. Sketch a T-v diagram and find the specified state for the following states a. Propane at critical temp & press find T(°C), p(bar) and v(m3 /kg) b. Water v=.05 m3 /kg, T=140°C find p(bar) c. Water at p=30 MPa, T=100°C find v(m3 /kg)

For a first order process G(s)= 4/(s+0.5): (a) Qualitatively sketch the pattern of the Bode diagram...

For a first order process G(s)= 4/(s+0.5): (a) Qualitatively sketch the pattern of the Bode diagram for this process, and indicate the limiting behaviors( i.e., the slopes and values as s --> 0 and s --> infinity) of ARn( the normalized amplitude ratio) and Phi ( the phase shift) in the plots. (b) Will a P-only control possibly make the process unstable? Show your reasoning based on the Bode stability criterion. (c) What if a delay term e^-5s is included,...

2. Consider the plane curve r(t) = <2cos(t),3sin(t)>. Parameterize the osculating circle at t=0. Sketch both...

2. Consider the plane curve r(t) = <2cos(t),3sin(t)>. Parameterize the osculating circle at t=0. Sketch both the curve and the osculating circle

Consider a firm with a constant marginal cost curve. Sketch the average cost curves( ATC, AFC,...

Consider a firm with a constant marginal cost curve. Sketch the average cost curves( ATC, AFC, AVC) and associated marginal cost curve. And explain why the cost curves would look as sketched.

Consider a firm with a constant marginal cost curve. Sketch the average cost curves( ATC, AFC,...

Consider a firm with a constant marginal cost curve. Sketch the average cost curves( ATC, AFC, AVC) and associated marginal cost curve. And explain why the cost curves would look as sketched.

Determine the t critical value(s) that will capture the desired t-curve area in each of the...

Determine the t critical value(s) that will capture the desired t-curve area in each of the following cases. (Round your answers to three decimal places.) (a) Central area = 0.95, df = 10 (b) Central area = 0.95, df = 20 (c) Central area = 0.99, df = 20 (d) Central area = 0.99, df = 60 (e) Upper-tail area = 0.01, df = 30 (f) Lower-tail area = 0.025, df = 5

Find and sketch the critical value(s) and the rejection region for a left-tailed t-test with α...

Find and sketch the critical value(s) and the rejection region for a left-tailed t-test with α =0.02 and n=42.

Question

Sketch constant preassure curve in T-s diagram.

Solutions

Expert Solution

Related Solutions

For each problem, sketch the appropriate process diagram on a T-v, P-v or P-h diagram 1)...

For each problem, sketch the appropriate process diagram on a T-v, P-v, or P-h diagram 4.60...

Sketch the curve given by the parametric equation x= tan(t) , y=sec (t) for -pi/2 <...

3. Sketch a T-v diagram and find the specified state for the following states a. Propane...

For a first order process G(s)= 4/(s+0.5): (a) Qualitatively sketch the pattern of the Bode diagram...

2. Consider the plane curve r(t) = <2cos(t),3sin(t)>. Parameterize the osculating circle at t=0. Sketch both...

Consider a firm with a constant marginal cost curve. Sketch the average cost curves( ATC, AFC,...

Consider a firm with a constant marginal cost curve. Sketch the average cost curves( ATC, AFC,...

Determine the t critical value(s) that will capture the desired t-curve area in each of the...

Find and sketch the critical value(s) and the rejection region for a left-tailed t-test with α...