Question

In: Mechanical Engineering

An engineer is conducted the centrifugal pump at aircraft hangar. The pump has an eye diameter...

An engineer is conducted the centrifugal pump at aircraft hangar. The pump has an eye diameter and an impeller diameter of 200 mm and 500 mm respectively while running at 900 rpm. While it rotate, the blade angle is measured at 35o at outlet with considering the tangent. The flow velocity is limited at 3 m/s constantly. Evaluate the

(a) inlet blade angle

(b) outlet absolute velocity with its angle at outlet and

(c) the manometric head.

Solutions

Expert Solution

Hence, All Answers are shown in the boxes.

Please Rate this,

Thank you..........


Related Solutions

A centrifugal pump has an eye diameter and an impeller diameter of 300 mm and 600...
A centrifugal pump has an eye diameter and an impeller diameter of 300 mm and 600 mm respectively while running at 850 rpm. When rotating, the blade angle is measured at 35o at the outlet with considering the tangent. The flow velocity is limited at 5 m/s constantly. Determine the following; (a) inlet blade angle (b) outlet absolute velocity with its angle at outlet and (c) the manometric head.
‏1. The impeller in a centrifugal pump has inner diameter as 125 mm and outer diameter...
‏1. The impeller in a centrifugal pump has inner diameter as 125 mm and outer diameter as 270 mm. The pump runs at 1400 rpm. The vane angles of impeller at inlet and outlet are 17° and 30° respectively. The water enters the impeller radially and velocity of flow is constant. Determine the work done by impeller per unit weight of water.
A centrifugal pump has the following characteristic: outer diameter of impeller 800 mm, width of impeller...
A centrifugal pump has the following characteristic: outer diameter of impeller 800 mm, width of impeller vanes at outlet 100 mm, angle of impeller vanes at outlet 40 o . The impeller runs at 550 rpm and delivers 0.98 m 3 /s of water under an effective head of 35 m. A 500 kW motor is used to drive the pump. Determine the manometric, mechanical and overall efficiencies of the pump. Assume water enters the impeller vanes radially at inlet....
A centrifugal pump with an impeller diameter of 30cm and speed 1800RPM operating at its best...
A centrifugal pump with an impeller diameter of 30cm and speed 1800RPM operating at its best effiecieny point develops a head of 30m and a flow of 3900L/min. while requiring power of 24kW. This pump is scaled up to provide a flow of 11000L/min. and a head of 75m. Determine the impeller diameter, speed, and a brake power of the new pump.
A model centrifugal pump with impeller diameter 365 mm is tested at its design operating condition....
A model centrifugal pump with impeller diameter 365 mm is tested at its design operating condition. The test gives the following data when pumping water, speed = 870 rev/min head = 18.9 m capacity = 73.7 L/s efficiency = 89%. A geometrically similar pump is to be designed to pump a fluid with relative density 0.78 against a head of 85 m with a flow of 450 L/s. Determine: A) The impeller size? B) The speed? C) The power input...
A centrifugal pump is to be used to pump water from a lake to a storage...
A centrifugal pump is to be used to pump water from a lake to a storage tank which is 165 feet above the surface of the lake. The pumping rate is to be 10 - 35 gal/min at a water temperature of 43°F. The water is used for drinking but will have to undergo filtration and chlorine treatment because there is sediment in the lake. The pump on hand can develop a discharge pressure of 60.0 psig pumping at a...
2. A centrifugal pump running at 750 rpm with a 1-m-diameter impeller generates the following pressure...
2. A centrifugal pump running at 750 rpm with a 1-m-diameter impeller generates the following pressure rise and flow rate data while pumping water at room temperature: ?(dot)[m^3/s]= [0, 0.0278, 0.0417, 0.0556, 0.0694, 0.0833, 0.0903, 0.0972] ?P [kPa]= [361, 349, 328, 293, 230, 145, 114, 59] Estimate the pressure rise and flow rate for impeller speeds of 500 and 1000 rpm using the 750 rpm data. Plot pressure rise (y-axis) vs flow rate (x-axis) for all three pump speeds and...
The radius of the impeller of a centrifugal pump at the inlet is 6 cm and...
The radius of the impeller of a centrifugal pump at the inlet is 6 cm and at the outlet is 10.5 cm. The blade angles β1 and β2 are respectively 33o and 21o respectively. The width of the impeller is uniform and 4.75 cm. The impeller rotates at 1200 rpm and pumps water (See Figure 1). Assuming radial entry, (a) the flow rate through the pump (b) the theoretical head (c) the power required assuming an efficiency of 75%. (d)...
Design a chain drive for a Centrifugal Pump to be driven by a Steam Turbine. The...
Design a chain drive for a Centrifugal Pump to be driven by a Steam Turbine. The input speed will be 1100 RPM, and the desired output speed is 350 RPM. The conveyor requires 20.0 hp. What type of lubrication will be needed?
1. Oil with a specific gravity of 0.75 is pumped by a centrifugal pump at 375...
1. Oil with a specific gravity of 0.75 is pumped by a centrifugal pump at 375 gpm, 19 hp, and 81% efficiency. Determine the pressure head in terms of: a) Feet of oil b) Feet of water answers: a) 217 ft b) 162 ft
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT