A precast T beam is to be used as a bridge over a small roadway. Concrete...

A precast T beam is to be used as a bridge over a small roadway. Concrete dimensions are b = 1500 mm, bw = 300 mm, hf = 150 mm, and h= 650 mm. The effective depth d= 500 mm. Concrete and steel strengths are f 'c= 40 MPa and fy = 420 MPa, respectively. Determine the design moment capacity of the girder. If the beam is used on a 10 m simple span, and if in addition to its own weight it must support railings, curbs, and suspended loads totaling 4 kN/m, what uniform service live load limit should be posted?

Expert Solution

Ally Wells answered 1 year ago

write an detailed essay on the type of concrete used for a bridge that has a...

write an detailed essay on the type of concrete used for a bridge that has a bridge deck of 170m

What will you propose for a concrete mix design to be used in constructing a bridge...

What will you propose for a concrete mix design to be used in constructing a bridge pier during a cold winter month. The bridge is designed to be constructed on a site where sulfate attack on the concrete is a problem. In this project, high cost is not allowed and the concrete’s cost must be priority without lowering quality.

How precast concrete piles could be assisted in penetration of soils

The concreting is going to be made for precast concrete. Choose the proper workability for the...

The concreting is going to be made for precast concrete. Choose the proper workability for the fresh concrete (find from the reference books and standards, and mention your reference in the homework report). Design an experiment to measure the workability of the concrete. Mention the method you are going to use to measure the workability and give the aimed value planned to obtain with the chosen method. Explain the experiment.

What are the advantages of a precast concrete structural frame? What are the disadvantages? Why is...

What are the advantages of a precast concrete structural frame? What are the disadvantages? Why is fireproofing used in a steel frame construction? How is cast-in-place concrete structural frame installed? How are cast-in-place structural members supported while they cure? What materials are used for formwork for columns? What trade installs the reinforcing steel in cast-in-place structures? How are bolted connection made during the construction of a steel framed building? What work is necessary on structural steel members prior to arriving...

Consider a concrete beam in an interior environment as follows: a. The beam is simply supported...

Consider a concrete beam in an interior environment as follows: a. The beam is simply supported with a design span of 4.8 metres. b. The dead load in the beam is uniformly distributed. c. Dead load on the beam, in addition to its own weight, is 6.9 KN/m of which 75% is permanent (long term). d. The beam carries a single concentrated live load at mid-span of 70 KN. e. 20% of the live load is considered short term. f....

What are the problems arised in simply supported beam bridge(any component of the bridge or steel...

What are the problems arised in simply supported beam bridge(any component of the bridge or steel trusses type) and how to improve the qualities or the problems arised?

A precast square concrete pile 305x305 mm in cross section is driven into ground using a...

A precast square concrete pile 305x305 mm in cross section is driven into ground using a steam hammer. If HE = 40 kN-m, E = 0.85, WR = 35 kN, weight of pile cap = 3.0 kN, L = 25 m, n = 0.4, Ep = 21 x 106 kN/m2 , number of blows for the last 25.4 mm pile penetration is 7 blows, unit weight of concrete = 24 kN/m3 . Compute the allowable pile capacity using: (a) Modified...

A reinforced concrete beam of normal weight concrete with an effective depth of 20 IN and...

A reinforced concrete beam of normal weight concrete with an effective depth of 20 IN and a width of 12 IN is reinforced with 3 IN2 of grade 60 (fy = 60 KSI) rebar. The beam has a concrete compressive strength f’c of 3000 PSI. (a) Determine the maximum ultimate moment which can be applied to the beam. (b) If the only dead load on the beam is self-weight, determine the allowable uniformly distributed live load which can be applied...

You are given the job of designing a bridge that is to be made of concrete...

You are given the job of designing a bridge that is to be made of concrete slabs that rest on a steel support frame. The total length of the bridge is 306 m, and you want to be sure that the expansion joints are sufficiently large. If the temperature increases by 22

Question