Question

In: Mechanical Engineering

a.Consider a component (you decide) in an aircraft that is subjected to creep. What standard creep...

a.Consider a component (you decide) in an aircraft that is subjected to creep. What standard creep reduction techniques would be best suited?

b.How does temperature affect creep rates and why?

c.Is there a difference between metals and plastics with creep failure?

d.Use the Hunt Library or a preferred one to explain constant stress or constant strain testing for plastics. What time scales are reasonable to test and determine with confidence?

Solutions

Expert Solution


Related Solutions

What is creep Creep failure Materials of creep Example of creep Design of creep
What is creep Creep failure Materials of creep Example of creep Design of creep
what is creep ? Discuss the theories propounded to explain probable causes of creep.
what is creep ? Discuss the theories propounded to explain probable causes of creep.
what is creep ? Discuss the theories propounded to explain probable causes of creep.
what is creep ? Discuss the theories propounded to explain probable causes of creep.
The average thickness of a flange on an aircraft component is found to be 1 mm...
The average thickness of a flange on an aircraft component is found to be 1 mm (from a sample of 36 measurements). a) Find the 95% and 99% confidence intervals for the mean thickness. Assume the population standard deviation is 0.1 mm. b) If we want to be 95% confident that our estimate of µ is off by less than 0.02 mm, how large of a sample is required?
A wing component on an aircraft is fabricated from an aluminum alloy that has a plane...
A wing component on an aircraft is fabricated from an aluminum alloy that has a plane strain fracture toughness of 30 MPa (m) 1/2 . It has been determined that fracture results at a stress of 120 MPa when the maximum internal crack length is 8.4 mm. For this same component and alloy, Compute the stress level at which fracture will occur for a critical internal crack length of 5.6 mm?
What two condition have to exist for Creep to occur?
What two condition have to exist for Creep to occur?
What are the typical ranges of drying shrinkage and creep strains in concrete; what is their...
What are the typical ranges of drying shrinkage and creep strains in concrete; what is their significance?
A company is trying to decide between making or buying a component in one of their...
A company is trying to decide between making or buying a component in one of their products. The fixed and variable costs for both options are given below: Cost                                                           Make Option                                  Buy Option Fixed Cost                                                   $25000                                             $3000 Variable Cost                                                 $8                                                     $12 a. Find the break-even quantity and the total cost at the break-even point. b. If the requirement is 4,500 units, is it more cost-effective for the firm to buy or make the components? What is the cost savings...
What does Scope Creep mean and why is it risky to a project? ……………………………………………………………………………………………… ……………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………… The...
What does Scope Creep mean and why is it risky to a project? ……………………………………………………………………………………………… ……………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………… The sum of knowledge including proven traditional practices that are widely applied, and innovative mechanisms that are emerging in the project management profession is referred to as ………………………………………………………………………. ……………………………………………………………………………………………… The ………………………………………………………. determines what is appropriate for any given project. Project requirements refer to …………………………………………………………….. ……………………………………………………………………………………………. Projects are not ongoing efforts. This means projects are …………………………….. and their durations are …………………………………… In ADM, a ‘dummy’ activity...
Mechanistically, what is the difference between Nabarro-Herring and Coble creep
Mechanistically, what is the difference between Nabarro-Herring and Coble creep
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT