A 3 phase 6 pole, asynchronous AC motor stator resistance 0.34 ohms rotor resistance 0.12 ohms...

A 3 phase 6 pole, asynchronous AC motor

stator resistance 0.34 ohms

rotor resistance 0.12 ohms

stator inductance of 0.5H

rotor inductance of 0.2H

magnetizing inductance 12.35

a)Draw the equivalent electrical circuit for this motor for 1 phase

b) is slip s=0.3 find the speed, torque, current at the stator and efficiency if the voltage supply is 240V per phase at 70 Hz with a Wye connection

Expert Solution

Manojponduru answered 1 year ago

A pump is being powered by a 3-phase asynchronous AC motor. Without using a variable speed...

A pump is being powered by a 3-phase asynchronous AC motor. Without using a variable speed drive, explain two ways that you can adjust the flow rate in the system. How does a VSD control the flow rate?

A 440 V 4-pole 3 phase 50 Hz slip ring induction motor has its stator winding...

A 440 V 4-pole 3 phase 50 Hz slip ring induction motor has its stator winding mesh connected and its rotor winding star connected. The standstill voltage measured between slip rings with the rotor open –circuited is 218 V. the stator resistance per phase is 0.6Ω and the stator reactance per phase is 3Ω. The rotor resistance per phase is 0.05Ω and the rotor reactance per phase is 0.25Ω. Calculate the maximum torque and the slip at which it occurs....

The parameters of a 3-phase, 4-pole, 50 Hz, Y-connected, wound-rotor induction motor are listed below. These...

The parameters of a 3-phase, 4-pole, 50 Hz, Y-connected, wound-rotor induction motor are listed below. These are the default values of the “Asynchronous Machine” model in MATLAB Simulink. r1=0.5968 ?; r2=0.6258 ?; L1=0.0003495 H; L2=0.005473 H; Lm=0.0354 H; Stator line voltage = 400 V rms. The motor for rotor speeds nm= 0 to 1500 rpm. X1= 0.1097 ohm, X2= 1.719 ohm , Xm= 11.12 ohm, RTH = 0.5853 , XTH = 0.1395 and VTH = 230.82 V. Suppose the motor...

•The rotor impedance at standstill of a three-phase, Y-connected, 208-V, 60Hz, 8-pole, wound-rotor induction motor is...

•The rotor impedance at standstill of a three-phase, Y-connected, 208-V, 60Hz, 8-pole, wound-rotor induction motor is 0.1 + j0.5 Ω/phase. •Determine the breakdown slip, (0.2) the breakdown (maximum) torque, (458.37 Nm) and the power developed by the motor at maximum torque (34.6kW). •What is the starting torque of this motor? (176.3 Nm) •Determine the resistance that must be inserted in series with the rotor circuit so that the starting torque is 50% of the maximum torque. (0.034Ω)

A three-phase asynchronous motor with squirrel cage rotor is available with: Voltage: 230/400 V Frequency: 50...

A three-phase asynchronous motor with squirrel cage rotor is available with: Voltage: 230/400 V Frequency: 50 Hz Number of Poles: 10 In addition, the following parameters of the equivalent circuit are known: R1 = 0.5  X1 = 3  R´2 = 0.8  X´2 = 3.5  Mechanical losses are considered to be negligible and the parallel branch of the equivalent circuit. 1. Draw the approximate equivalent circuit of the motor without the branch in parallel. 2. Indicates the...

A motor with an internal resistance of R(motor) = 50 Ohms requires a potential difference of...

A motor with an internal resistance of R(motor) = 50 Ohms requires a potential difference of V(motor)=20V to work properly. As you don't have a 20V power source, you place two 12V batteries in series with a custom-built resistor with resistance R1. (a) How much current moves through the motor when it is working properly? (b) What must be the resistance of your custom-built resistor so that the potential difference across the motor is 20V? (c) If you built your...

A 6-pole, 50 Hz, 3-phase induction motor running on full load develops a useful torque of...

A 6-pole, 50 Hz, 3-phase induction motor running on full load develops a useful torque of 160 Nm when the rotor emf makes 120 complete cycles per minute. The windage and friction loss is 1005.30 Watt. It is assumed; the core loss is lumped together with the windage and friction loss. The total stator loss is given to be 800 Watt. Compute: a) Shaft power output, b) The copper loss in the rotor winding,c) The input power to the motor, and d) The...

Explain the principle of each method of speed control: Variable stator voltage control, Rotor resistance control,...

Explain the principle of each method of speed control: Variable stator voltage control, Rotor resistance control, Frequency control. Explain the advantages and disadvantages for each method of speed control: Variable stator voltage control, Rotor resistance control, Frequency control. Excuse me teacher, could you help me to answer these questions by typing but not writing? Thanks teacher.

A 3-phase, 380 V, 50 Hz , 6 pole, Y-connected induction motor has R1 = 0.1...

A 3-phase, 380 V, 50 Hz , 6 pole, Y-connected induction motor has R1 = 0.1 W , X1 = 0.4 W, R2’ = 0.12 W , X2’ = 0.4 W, Xm = 20 W , Pr = 1 kW. The motor is operated at 970 rpm what is the efficiency?

A4-pole,250V, 50Hz single phase induction motor has rotor frequency 2 Hz, in starting has following parameters:...

A4-pole,250V, 50Hz single phase induction motor has rotor frequency 2 Hz, in starting has following parameters: main winding Rm=2 Ω ,Xm=4 Ω and staring winding : Rs =4 Ω , XLS=2 Ω ,Xcs=8 Ω. Find : speed of motor, Im , IS, θm θs, α and p.f.

Question