R-134a flows in a horizontal 8 mm diameter circular tube. The mass flux is 400 kg/m2s,...

R-134a flows in a horizontal 8 mm diameter circular tube. The mass flux is 400 kg/m2s, the entering quality is 0.0, and the existing quality is 0.8. The tube length is 3 m. Assuming a constant saturation temperature of 20°C, plot the variation of hTP as a function of x.

Expert Solution

samet mamat answered 2 years ago

Ethyl alcohol flows through a horizontal tube having a diameter of 25 mm. If the mean...

Ethyl alcohol flows through a horizontal tube having a diameter of 25 mm. If the mean velocity is 0.18 m/s, what is the magnitude of the pressure drop per unit length along the tube (in Pa/m)? What is the velocity at a distance of 5 mm from the tube axis (in m/s)?

Consider a 9 mm diameter circular tube, calculate the length of tube that is required to...

Consider a 9 mm diameter circular tube, calculate the length of tube that is required to transfer 100 W of water that circulates through the tube at a rate of 0.08 kg / s. The temperature of the water is kept constant at 50 ° C and the wall of the tube is maintained at 45 ° C.

A circular plate having a diameter of 330 mm is held perpendicular to an axisymmetric horizontal...

A circular plate having a diameter of 330 mm is held perpendicular to an axisymmetric horizontal jet of air having a velocity of 43 m/s and a diameter of 88 mm as shown in the figure below. A hole at the center of the plate results in a discharge jet of air having a velocity of 43 m/s and a diameter of 22 mm. Determine the horizontal component of force required to hold the plate stationary. F = N the...

A horizontal tube of 53-mm outer diameter, with a surface temperature of 34 degrees Celsius, is...

A horizontal tube of 53-mm outer diameter, with a surface temperature of 34 degrees Celsius, is exposed to steam at 0.22 bar. Estimate the condensation rate and heat transfer rate per unit length of the tube.

Water at 35°C is pumped through a horizontal, 200-m-long, 30-mm-diameter tube at 0.25 kg/s. Over time,...

Water at 35°C is pumped through a horizontal, 200-m-long, 30-mm-diameter tube at 0.25 kg/s. Over time, a 2-mm-thick layer of scale of surface roughness e = 200 µ m is deposited on the interior tube wall. Determine the pressure drop from the entrance to the exit of the tube and the required pump power for the clean and fouled conditions.

At the center of a 50-mm-diameter circular ice rink, a 76 kg skater traveling north at...

At the center of a 50-mm-diameter circular ice rink, a 76 kg skater traveling north at 2.7 m/s collides with and holds onto a 61 kg skater who had been heading west at 3.8 m/s . How long will it take them to glide to the edge of the rink? Express your answer using two significant figures. Where will they reach it? Give your answer as an angle north of west.

A horizontal Venturimeter with inlet diameter 300 mm and throat diameter 150 mm is used to...

A horizontal Venturimeter with inlet diameter 300 mm and throat diameter 150 mm is used to measure the flow of water. The pressure at inlet is 24 N/cm2 and the vacuum pressure (p2)at the throat is 320 mm of mercury. Find the discharge and velocity through the pipe .The value of Cd may be taken as 0.98.

A tube with a diameter of 6.45 mm was placed in a liquid with a density...

A tube with a diameter of 6.45 mm was placed in a liquid with a density of 998 kg / m3 and it was observed that the liquid increased by 1.44 mm in the tube. Find the surface tension of the fluid [N / m] by taking the contact angle 15 ° between the liquid and the tube surface.

A current of 5 mA flows through a 2 mm inner-diameter glass tube filled with 1.0...

A current of 5 mA flows through a 2 mm inner-diameter glass tube filled with 1.0 mol dm-3 NaCl(aq) solution in the anode compartment in addition to a CH3COONa (aq) solution in the cathode compartment. The boundary created between the two solutions moves 6.05 mm towards the anode in 10 minutes. Calculate the transport number of the chloride ion in the solution.

A tube has a diameter of 0.87 mm and is placed vertically in a liquid of...

A tube has a diameter of 0.87 mm and is placed vertically in a liquid of density 879 km/m^3, which rises 3.7 cm in the tube. The contact angle is 17 degrees between the liquid and tub. What is the surface tension of the liquid?

Question