Question

In: Electrical Engineering

Question 5 The following test data was captured from a 15hp, 4-pole, 400V, Design A, Induction...

Question 5
The following test data was captured from a 15hp, 4-pole, 400V, Design A, Induction motor. The star-connected machine has a rated current of 50A.
No-Load Test
VT = 400V
f = 50Hz
IA = 12A
Pin = 650W
IB = 12.1A
IC = 12.05A
16
DC Test
V = 15V
I = 50A
Locked Rotor Test
VT = 35V
f = 15Hz
IA = 50.1A
Pin = 1850W
IB = 49.5A
IC = 48.75A
5.1
Calculate the parameters of the equivalent circuit.
(7)
5.2
Draw and label the equivalent circuit and include the calculated values of the respective circuit parameters.
(3)
5.3
Find the slip at the pull-out torque. Calculate the pull-out torque.
(5)
[15]

Solutions

Expert Solution


Related Solutions

A 400V, three phase, 50Hz, 4 pole induction motor is operating at a per unit slip...
A 400V, three phase, 50Hz, 4 pole induction motor is operating at a per unit slip of 40KW from the suppply. Under these conditions stator losses amount to 2.2 KW and rotational losses due to friction and windage amount to 1.4KW. Calculate the net horsepower and torque developed.
A 400V, 2 pole, 50 Hz, three-phase induction motor is drawing 60 A at 0.85 PF...
A 400V, 2 pole, 50 Hz, three-phase induction motor is drawing 60 A at 0.85 PF lagging. The stator copper losses are 2 kW, the stator core losses are 1.8 kW and rotor copper losses are 700 W. The friction and windage losses are 600 W, the stray loss 100 W, and rotor core loss 100 W. Find the following quantities: a. The air gap power. b. The developed mechanical power. c. The output power. d. The efficiency of the...
Problem 5: The following data refers to a 10-pole, 200 V, 50 Hz, 3 phase induction...
Problem 5: The following data refers to a 10-pole, 200 V, 50 Hz, 3 phase induction motor? R1 = 3.5 ohm, X1 = 11 ohm, R`2 = 13.2 ohm. When the motor is tested on no-load, its observed that it takes 7.6 A (line current) and the total core loss is 620 W. B y using an approximate equivalent circuit at 8% slip, Calculate; The rotor current The supply current and power factor Mechanical power developed. Gross load torque Determine...
The following test data apply to a 110 kVA, 2300 V three-phase four-pole 60 Hz induction...
The following test data apply to a 110 kVA, 2300 V three-phase four-pole 60 Hz induction motor. No load test at rated voltage and frequency: Load current = 8.1 A, Three-phase power = 3025 W Blocked-rotor test at rated current and 15 Hz: Line voltage = 268 V, Three-phase power = 10.2 kW Stator resistance between line terminals = 2.34 Ω. Compute the stator current and power factor, kW output, and efficiency when this motor is operating at rated voltage...
A 3 phase 460 V, 60 Hz, 4 pole, delta connected induction motor has the following...
A 3 phase 460 V, 60 Hz, 4 pole, delta connected induction motor has the following equivalent circuit parameters. Rs = 0.42 Ω, Rr = 0.23 Ω, Xs = Xr = 0.82 Ω. Xm = 22 Ω. The no load loss = 60 W and may be assumed constant. The rotor speed is 1750 rpm. Use the approximate equivalent circuit ( i.e. the Xm branch is at the very left of the circuit) determine the following a. the synchronous speed...
A 460 V 25 Hp, 60 Hz, 4-pole, Y-connected induction motor has the following parameters in...
A 460 V 25 Hp, 60 Hz, 4-pole, Y-connected induction motor has the following parameters in ohms per phase referred to the stator circuit. R1= 0.641 W R2= 0.332 W   X1= 1.106 W X2=0.464 W Xm=26.3 W The rotational losses are 1100 W and are assumed to be constant. The core loss is included in this figure. The motor is supplied at rated voltage and rated frequency. Calculate; Synchronous speed Slip at which maximum torque occurs The maximum torque of...
For full load operation of 60Hz, 380V, 4 pole 30kW induction motor, the speed is 1746rpm,...
For full load operation of 60Hz, 380V, 4 pole 30kW induction motor, the speed is 1746rpm, input current 56.2A power factor 90%. In no load operation, input current 17.3A, power factor 13.5%. In full load operation, assume that the mechanical loss is 25% of the total loss and no other losses. a) Iron loss load efficiency b) Find a rotor copper loss under full load c) Iron loss d) Find a fixed automatic hand under full load e) Find the...
Question 4 Consider the following hypotheses: H0: mean = 5 H1: mean < 5 A test...
Question 4 Consider the following hypotheses: H0: mean = 5 H1: mean < 5 A test is performed with a sample of size 25. The sample mean was 4.67 and the population standard deviation is 1.2. Assume that the population is approximately normal. Use the TI-84 PLUS calculator to compute the P-value. Question 5 Consider the following hypotheses: H0: mean = 9 H1: mean > 9 A test is performed with a sample of size 49. The sample mean was...
A 37.3 kW 4 pole 50 Hz induction machine has a friction windage torque of 22...
A 37.3 kW 4 pole 50 Hz induction machine has a friction windage torque of 22 N-m. the stator losses equal the rotor circuit loss. Calculate: The input power to the stator when delivering full-load output at a speed of 1.440 rev/min [44000 W] The gross input and stator output power when running at a speed of 1560 rev/min. the stator losses are as in (a) and the windage and friction torque is unchanged [291 N-m; 40300 W]
Q3). A 10KW, 415V, 50Hz, 4 pole, Y (star)-connected induction motor is running at 1425 rpm...
Q3). A 10KW, 415V, 50Hz, 4 pole, Y (star)-connected induction motor is running at 1425 rpm and is delivering full load output while operating at 89% efficiency. a) Find the total losses of the motor [4 marks] b) If the Copper loss, Core loss and Rotational loss are at a ratio of 1:0.7:0.2, find each loss separately [6 marks] c) What is the torque output of the motor? [4 marks] d) If the full load power factor is 0.85, what...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT