Question

In: Mechanical Engineering

A steam generator consists of a bank of stainless stell (k=15 W/m·K) tubes habing the core...

A steam generator consists of a bank of stainless stell (k=15 W/m·K) tubes habing the core configuration of CF7.0-5/8J and an inner diameter of 13.8 mm. The tubes are installed in a plenum whose square cross section is 0.6 m on a side, thereby providing a frontal area of 0.36 m2. Combustion gases whose propertires may be aproximated as those of atmospheric air, enter the plenum at 900 k and pass in cross flow over the tubes at 3 kg/s. There are 11 rows of tubes in the gas flow direction. If saturated water at 2.455 bar experiences boiling in the tubes, what is the gas exit temperature? A convection coeficient of 10.000 W/m2·K is associated with boiling in the tubes.

Solutions

Expert Solution


Related Solutions

A steam generator consists of a bank of stainless stell (k=15 W/m·K) tubes habing the core...
A steam generator consists of a bank of stainless stell (k=15 W/m·K) tubes habing the core configuration of CF7.0-5 and an inner diameter of 13.8 mm. The tubes are installed in a plenum whose square cross section is 0.6 m on a side, thereby providing a frontal area of 0.36 m2. Combustion gases whose propertires may be aproximated as those of atmospheric air, enter the plenum at 900 k and pass in cross flow over the tubes at 3 kg/s....
A wall is constructed of two layers of 2-cm-thick sheetrock (k = 0.17 W/m·K) separated by...
A wall is constructed of two layers of 2-cm-thick sheetrock (k = 0.17 W/m·K) separated by 16 cm by wood studs (k = 0.11 W/m·K) whose width is 5 cm. The studs are placed vertically 55 cm apart, and the space between them is filled with stagnant air (16 by 55 cm) as insulation (k = 0.026 W/m·K). Pay attention to the measurements! The house is maintained at 20°C and the ambient temperature outside is ?9°C. Taking the heat transfer...
A long solid bar (k = 28 W/m·K and α = 12 × 10−6 m2/s) of...
A long solid bar (k = 28 W/m·K and α = 12 × 10−6 m2/s) of square cross section is initially at a uniform temperature of 32°C. The cross section of the bar is 20 cm × 20 cm in size, and heat is generated in it uniformly at a rate of ??̇ = 8 × 105 ??⁄??2. All four sides of the bar are subjected to convection to the ambient air at T∞ = 30 °C with a heat...
3. A stainless steel sphere of thermal conductivity 16 W/m · K with a diameter of...
3. A stainless steel sphere of thermal conductivity 16 W/m · K with a diameter of 4 cm is exposed to a convective environment of 15 W/m2 · K, 20?C. Heat is generated uniformly in the sphere at a rate of 1.0 MW/m3 . Determine the steady-state temperature of the sphere at its center and its surface. Also determine the heat flux at a radius of 1.5 cm.
Steam at a temperature of 280 DegreeC flows in a steel pipe (k=70 W/m K) having...
Steam at a temperature of 280 DegreeC flows in a steel pipe (k=70 W/m K) having an inner and outer diameter of 5 cm and 5.6 cm. The pipe is covered with glass wool insulation (k=0.05 W/m K) to a thickness of 4 cm. On a windy day heat is lost from the lagging surface with a convective heat transfer coefficient of 50 W/m2 K. The surroundings are at a temperature of 5 DegreeC and the internal heat transfer coefficient...
USE EXCEL TO SOLVE After heat treatment, the 2-cm thick metal plates (k = 180 W/m·K,...
USE EXCEL TO SOLVE After heat treatment, the 2-cm thick metal plates (k = 180 W/m·K, ρ = 2800 kg/m3, and cp = 880 J/kg·K) are conveyed through a cooling chamber with a length of 10 m. The plates enter the cooling chamber at an initial temperature of 500°C. The cooling chamber maintains a temperature of 10°C, and the convection heat transfer coefficient is given as a function of the air velocity blowing over the plates h = 33V0.8, where...
A long, cylindrical, electrical heating element of diameter D= 10 mm, thermal conductivity k= 240 W/m·K,...
A long, cylindrical, electrical heating element of diameter D= 10 mm, thermal conductivity k= 240 W/m·K, density ρ= 2700 kg/m3, and specific heat cp= 900 J/kg·K is installed in a duct for which air moves in cross flow over the heater at a temperature and velocity of 27°C and 15 m/s, respectively. (a) Neglecting radiation, estimate the steady-state surface temperature when, per unit length of the heater, electrical energy is being dissipated at a rate of 1500 W/m. (b) If...
Q.8. Super-heated steam at 875 K is flowing through a thick walled tube of stainless tube...
Q.8. Super-heated steam at 875 K is flowing through a thick walled tube of stainless tube with inside diameter 40mm and outside diameter50mm such that its inner wall is heated to a uniform temperature of 875K.To reduce heat loss, the tube is lagged with 30mm layer of asbestos insulation k=0.2 W/m.K. Calculate the heat loss using the electrical analogy per metre length if the outer surface temperature of the insulated tube is 350K.Thermal conductivity of steel=19 W/m.k.
A thick steel slab (ρ= 7800 kg/m3, c= 480 J/kg·K, k= 50 W/m·K) is initially at...
A thick steel slab (ρ= 7800 kg/m3, c= 480 J/kg·K, k= 50 W/m·K) is initially at 300°C and is cooled by water jets impinging on one of its surfaces. The temperature of the water is 25°C, and the jets maintain an extremely large, approximately uniform convection coefficient at the surface. Assuming that the surface is maintained at the temperature of the water throughout the cooling, how long will it take for the temperature to reach 50°C at a distance of...
4-23 After heat treatment, the 2-cm thick metal plates (k = 180 W/m·K, ρ = 2800...
4-23 After heat treatment, the 2-cm thick metal plates (k = 180 W/m·K, ρ = 2800 kg/m3, and cp = 880 J/kg·K) are conveyed through a cooling chamber with a length of 10 m. The plates enter the cooling chamber at an initial temperature of 500°C. The cooling chamber maintains a temperature of 10°C, and the convection heat transfer coefficient is given as a function of the air velocity blowing over the plates h = 33V0.8, where h is in...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT